Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

When the stop light switch is turned on, the current flows to the stop lights to illuminate.

WIRING DIAGRAM


E151496E01


INSPECTION PROCEDURE

1.INSPECT FUSE (STOP)
  1. Remove the STOP fuse from the No. 2 engine room relay block.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω

  1. Reinstall the STOP fuse.



NG
REPLACE FUSE
OK


2.INSPECT BULB (REAR STOP LIGHT BULB)
B141038E03
B141590E01
  1. Remove the rear stop light bulbs.

  1. Remove the high mounted stop light assembly.

  1. Apply battery voltage to the terminals and check that the rear stop light and high mounted stop light illuminates.

    OK:
    Rear stop light 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 3
    Negative battery - Terminal 1
    Stop light bulb illuminates
    High mounted stop light 
    Measurement Condition
    Specified Condition
    Positive battery - Terminal 2
    Negative battery - Terminal 1
    High mounted stop light illuminates

  1. Reinstall the rear stop light bulbs.

  1. Reinstall the high mounted stop light assembly.

Result:
Result
Proceed to
OK
A
NG (Rear stop light)
B
NG (High mounted stop light)
C



B
REPLACE BULB

C
REPLACE HIGH MOUNTED STOP LIGHT ASSEMBLY (Click here)
A


3.INSPECT STOP LIGHT SWITCH


    B113724E04
  1. Remove the stop light switch.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    3 - 4
    Switch pin pushed in
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin released
    Below 1 Ω

  1. Reinstall the stop light switch.



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


4.INSPECT STOP LP CTRL RELAY


    C083933E02
  1. Remove the STOP LP CTRL relay from the No. 2 engine room relay block.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 4
    Apply the battery voltage between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply the battery voltage between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the STOP LP CTRL relay.



NG
REPLACE STOP LP CTRL RELAY
OK


5.CHECK HARNESS AND CONNECTOR (FUSE - STOP LIGHT SWITCH)


    B124046E08
  1. Disconnect the A3 stop light switch connector.

  1. Measure the voltage according value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A3-2 - Body ground
    Always
    11 to 14 V

  1. Reconnect the stop light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - STOP LIGHT CONTROL RELAY)


    B136076E02
  1. Disconnect the A3 stop light switch connector.

  1. Remove the STOP LP CTRL relay from the No. 2 engine room relay block.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A3-1 - STOP LP CTRL relay terminal 4
    Always
    Below 1 Ω
    A3-1 or STOP LP CTRL relay terminal 4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch connector.

  1. Reinstall the STOP LP CTRL relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - REAR STOP LIGHT)


    B136077E02
  1. Remove the STOP LP CTRL relay from the No. 2 engine room relay block.

  1. Disconnect the L11 and L14 rear stop light connectors.

  1. Disconnect the T1 high mounted stop light connector.

  1. Measure the resistance according value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP LP CTRL relay terminal 3 - L11-3
    Always
    Below 1 Ω
    STOP LP CTRL relay terminal 3 - L14-3
    Always
    Below 1 Ω
    STOP LP CTRL relay terminal 3 - T1-2
    Always
    Below 1 Ω
    STOP LP CTRL relay terminal 3 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the STOP LP CTRL relay.

  1. Reconnect the stop light connectors.

  1. Reconnect the high mounted stop light connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR STOP LIGHT - BODY GROUND)