Home › BODY › INTERIOR › ROOF HEADLINING

ROOF HEADLINING > REMOVAL

for Preparation Click here



1. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH


    B130749
  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Disengage the 10 clips and remove the rear seatback board carpet.



2. REMOVE REAR SEATBACK ASSEMBLY RH


    B135127
  1. Pull up the rear seatback.

  1. Remove the bolt and the anchor plate of the rear center seat outer belt.



    B130750
  1. Remove the rear seat inner belt from the rear seatback holder.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear seatback.



3. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH


    B130720
  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Disengage the 8 clips and remove the rear seatback board carpet.



4. REMOVE REAR SEATBACK ASSEMBLY LH


    B130721
  1. Remove the rear center seat inner belt from the rear seatback holder.

  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear seatback.



5. REMOVE REAR FLOOR BOARD


    B135073E04
  1. Remove the bolt and the luggage hold belt striker.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side

    HINT:
    Use the same procedure for both sides.



    B135075
  1. Disengage the clip and the claw and remove the rear floor board.



6. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B130592
  1. Remove the 5 screws.



    B130593
  1. Disengage the 11 claws and remove the rear floor mat support plate.



7. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


B179163E03

HINT:
Use the same procedure for both sides.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Remove the cap.

  1. Remove the bolt and the luggage hold belt striker.



8. REMOVE REAR FLOOR MAT ASSEMBLY


    B130594
  1. Using a clip remover, remove the 2 clips and the rear floor mat.



9. REMOVE FRONT DOOR SCUFF PLATE RH


    B130597
  1. Disengage the 14 claws and remove the front door scuff plate.



10. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



11. REMOVE ACCESS DOOR SCUFF PLATE RH


    B130598
  1. Disengage the 6 claws and remove the access door scuff plate.



12. REMOVE ACCESS DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



13. REMOVE FRONT FLOOR FOOTREST


    B130586
  1. Disengage the 4 claws and remove the front floor footrest.



14. REMOVE FOOTREST CLIP


    B130587
  1. Remove the 2 footrest clips.



15. REMOVE COWL SIDE TRIM BOARD RH


    B130599
  1. Remove the clip.

  1. Disengage the 2 claws and remove the cowl side trim board.



16. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



17. REMOVE ROOF SIDE INNER GARNISH COVER RH


B130600E02

HINT:
Use the same procedure for both sides.

Text in Illustration 
*1
Protective Tape
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the roof side inner garnish cover.



18. REMOVE ROOF SIDE INNER GARNISH COVER LH

HINT:
Use the same procedure as for the RH side.



19. REMOVE ROOF SIDE RAIL GARNISH RH


    B267104
  1. Remove the 2 bolts.

  1. Disengage the claw and the guide remove the roof side rail garnish.



20. REMOVE ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.



21. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B130603
  1. Remove the front door opening trim weatherstrip.



22. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



23. REMOVE ASSIST GRIP PLUG


B175647E03

HINT:
Use the same procedure to remove all the assist grip plugs.

Text in Illustration 
*1
Protective Tape
*a
for RH Side
*b
for LH Side
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.



24. REMOVE ASSIST GRIP ASSEMBLY


B175648E03

HINT:
Use the same procedure to remove all the assist grips.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Remove the 2 screws and the assist grip.



25. REMOVE VISOR SUB-ASSEMBLY RH


    B177923E03
  1. Disengage the 2 claws and remove the visor sub-assembly.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side



26. REMOVE VISOR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



27. REMOVE FRONT PILLAR GARNISH RH


    B267110
  1. Disengage the 2 clips and the guide and remove the front pillar garnish.



28. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure as for the RH side.



29. REMOVE DECK SIDE GARNISH (w/ Woofer)


    B271490
  1. Disengage the 6 claws and remove the rear deck side garnish.



30. REMOVE SPEAKER MOUNTING COVER (w/ Woofer)


    E220885
  1. Disengage the 8 clips and 2 guides and remove the speaker mounting cover.



31. REMOVE AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)


    E220886
  1. Disconnect the connectors.

  1. Remove the 4 bolts and the amplifier box speaker.



32. REMOVE PACKAGE HOLDER NET HOOK


B271495E01

HINT:
Use the same procedure to remove all the package holder net hooks.

Text in Illustration 
*a
for RH Side without Woofer
*b
for LH Side
  1. Remove the screw and the package holder net hook.



33. REMOVE QUARTER TRIM POCKET TRAY (w/o Woofer)


    B130611
  1. Disengage the 7 claws and remove the quarter trim pocket tray.



34. REMOVE SIDE TRIM COVER (w/o Woofer)


    B267111
  1. Disengage the 6 claws and the 2 guides remove the side trim cover.



35. REMOVE QUARTER TRIM POCKET (w/o Woofer)


    B130613
  1. Disengage the 6 claws and remove the quarter trim pocket.



36. REMOVE LAP BELT OUTER ANCHOR COVER


B130614E04

HINT:
Use the same procedure for both sides.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



37. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH


    B130615
  1. Remove the bolt and the anchor plate.



38. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



39. REMOVE REAR DECK TRIM COVER (w/ Power Outlet Socket)


    B135130
  1. Disengage the 8 claws and remove the rear deck trim cover.



    B138600
  1. Disconnect the power outlet connector.



40. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    B130616
  1. Remove the 3 screws and bolt.



    B130617
  1. Disengage the 6 clips and the 8 claws and remove the deck trim side panel.



41. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    B130618
  1. Remove the 3 screws.



    B130619
  1. Disengage the 6 clips and the 8 claws and remove the deck trim side panel.



42. REMOVE ROOF SIDE INNER GARNISH RH


    B130620E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B267112
  1. Remove the bolt and the clip.

  1. Disengage the 7 clips and the guide and remove the roof side inner garnish.

  1. Pass the rear seat outer belt through the slit in the roof side inner garnish.



43. REMOVE ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



44. REMOVE ROOF HEADLINING HOLE PLUG


B130623E04

HINT:
Use the same procedure for both sides.

Text in Illustration 
*1
Protective Tape
*a
for RH Side
*b
for LH Side
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.



    B130625E04
  1. Remove the bolt.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side

  1. Disengage the claw and remove the roof headlining hole plug.



45. REMOVE COAT HOOK


B130626E04

HINT:
Use the same procedure for both sides.

Text in Illustration 
*1
Protective Tape
*a
for RH Side
*b
for LH Side
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.



    B130628E04
  1. Remove the bolt and the coat hook.
    Text in Illustration 
    *a
    for RH Side
    *b
    for LH Side



46. REMOVE VISOR ASSEMBLY RH


    B130629
  1. Remove the visor support shaft from the visor holder.

  1. Remove the 2 screws and the visor.



47. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



48. REMOVE VISOR HOLDER


B130630E04

HINT:
Use the same procedure for both sides.

Text in Illustration 
*a
for RH Side
*b
for LH Side
  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.



49. REMOVE INNER REAR VIEW MIRROR ASSEMBLY
(Click here)


50. REMOVE ROOM LIGHT ASSEMBLY


B138411

HINT:
The procedure described below is for the front side. Use the same procedure for both the front and rear sides, unless otherwise specified.



    B138408E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
    Text in Illustration 
    *1
    Protective Tape



    E114442E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.
    Text in Illustration 
    *1
    Protective Tape



    B138413E02
  1. for Front Side:
    Text in Illustration 
    *1
    Protective Tape

    1. Remove the 2 wire harnesses from the 2 claws of the room light.

    2. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.



    B138412E02
  1. for Rear Side:
    Text in Illustration 
    *1
    Protective Tape

    1. Remove the wire harness from the claw of the room light.

    2. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.



51. REMOVE NO. 1 PERSONAL LIGHT LENS (w/o CRAWL)


B205289E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the No. 1 personal light lens.



52. REMOVE NO. 2 PERSONAL LIGHT LENS (w/o CRAWL)

HINT:
Perform the same procedure as for the RH side.



53. REMOVE PERSONAL LIGHT ASSEMBLY (w/o CRAWL)


B205290E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.

  1. Disconnect the connector, and remove the personal light.



54. REMOVE PERSONAL LIGHT ASSEMBLY (w/ CRAWL)


    E260472
  1. Using a moulding remover, disengage the 4 clips and 4 guides.



    E260473E01
  1. Disconnect the connector and remove the personal light assembly.
    Text in Illustration 
    *1
    Grommet
    *2
    Pin

  1. Remove the 4 pins.

  1. Remove the 4 grommets from the body side.



55. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B133853
  1. Disengage the 4 clips and 2 claws and remove the instrument panel register.

    NOTICE:
    1. To avoid breakage of the register, remove the instrument panel register with the shut damper of the register open.
    2. Pull the instrument panel register up diagonally to remove it.



56. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B133859
  1. Disengage the 3 claws and separate the hood lock control lever.



57. REMOVE INSTRUMENT PANEL FINISH LOWER PANEL SUB-ASSEMBLY


    B133860
  1. Remove the 2 <F> bolts.

  1. Disengage the 5 clips and claw and remove the lower instrument panel finish panel.

  1. Disconnect the connector.



58. REMOVE ROOF HEADLINING


    B328601E01
  1. Remove the wire harness from the 2 clamps.
    Text in Illustration 
    *A
    w/o CRAWL
    *B
    w/ CRAWL

  1. w/o CRAWL:

    1. Disconnect the 2 connectors.

  1. w/ CRAWL:

    1. Disconnect the 3 connectors.

  1. Using a clip remover, disengage the clamp.



    B208620
  1. Using a clip remover, disengage the 4 clamps.



  1. w/ Satellite Radio:



      B271557
    1. Using a clip remover, disengage the clamp and disconnect the antenna cord connector.



    2. B271558
    3. Disconnect the antenna cord connector.



  1. Using a clip remover, remove the 4 clips.


    B130645



    B130646
  1. Remove the roof headlining from the back door.