Home › BODY › SEAT › REAR SEAT ASSEMBLY (for RH Side)

REAR SEAT ASSEMBLY (for RH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR SEATBACK COVER


    B130775E02
  1. Using hog ring pliers, install the rear seatback cover with 8 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the rear seatback cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.

  1. Pass the hook of the rear seatback cover through the slit in the rear seatback pad.



2. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    B135154
  1. Install the retractor with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.



3. INSTALL REAR SEATBACK LOCK ASSEMBLY


    B130772
  1. Install the rear seatback lock with the 2 bolts.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }



4. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY


    B130768
  1. Install the rear seatback frame.



    B130767E02
  1. Using hog ring pliers, install 17 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers



    B135129E02
  1. Install the belt of the rear center seat outer belt into the rear seatback cover band.
    Text in Illustration 
    *1
    Band



5. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B130771
  1. Engage the 2 claws and install the rear seatback stop button grommet.



6. INSTALL REAR SEATBACK LOCK RELEASE BUTTON


    B130773
  1. Install rear seatback lock release button.



7. INSTALL REAR SEAT HEADREST SUPPORT


B130770E02
Text in Illustration 
*a
Protrusion

HINT:
Use the same procedure to install all the rear seat headrest supports.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.



8. INSTALL TETHER ANCHOR COVER


B130765

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the tether anchor cover.



    B130763
  1. Engage the 3 claws and close the cover.



9. INSTALL REAR SEATBACK LOCK COVER


    B271143
  1. Engage the guide and install the rear seatback lock cover.

  1. Tighten the screw.



10. INSTALL REAR SEAT SHOULDER BELT COVER


    B267855
  1. Engage the 4 claws and install the rear seat shoulder belt cover.



11. INSTALL SHOULDER BELT ANCHOR COVER


    B267854
  1. Engage the 2 claws and 2 hooks and install the shoulder belt anchor cover.



12. INSTALL REAR SEAT HEADREST HANDLE


    B271552
  1. Install the snap ring to the rear seat headrest handle.



    B271553
  1. Install the rear seat headrest handle as shown in the illustration.



13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



14. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



15. INSTALL REAR SEAT CUSHION COVER


    B130757E02
  1. Using hog ring pliers, install the rear seat cushion cover with 10 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the rear seat cushion cover.
    2. When installing the hog rings, minimize wrinkles as far as possible.



16. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY


    B130755
  1. Engage the hook and install the rear seat cushion frame.



17. INSTALL REAR SEAT CUSHION STOPPER


    B130754
  1. Install the rear seat cushion stopper with the screw.



18. INSTALL REAR SEAT CUSHION UNDER COVER


    B130753E02
  1. Insert the rear seat cushion stopper into the slit of the rear seat cushion under cover.
    Text in Illustration 
    *1
    Band

  1. Install the rear seat cushion under cover with the 8 clips.

  1. Install the rear seat cushion stopper into the rear seat cushion cover band.



19. INSTALL REAR SEAT CUSHION HINGE SUB-ASSEMBLY


B267732

HINT:
Use the same procedure for both sides.

  1. Engage the hook and install the rear seat cushion hinge.

  1. Install the rear seat cushion hinge with the bolt.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }