Home › RESTRAINTS › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY

REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    B135154
  1. Install the retractor with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.



2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY


    B130768
  1. Install the rear seatback frame.



    B130767E02
  1. Using hog ring pliers, install 17 new hog rings.
    Text in Illustration 
    *1
    New Hog Ring
    *2
    Hog Ring Pliers



    B135129E02
  1. Install the belt of the rear center seat outer belt into the rear seatback cover band.
    Text in Illustration 
    *1
    Band



3. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B130771
  1. Engage the 2 claws and install the rear seatback stop button grommet.



4. INSTALL REAR SEATBACK LOCK RELEASE BUTTON


    B130773
  1. Install rear seatback lock release button.



5. INSTALL REAR SEAT HEADREST SUPPORT


B130770E02
Text in Illustration 
*a
Protrusion

HINT:
Use the same procedure to install all the rear seat headrest supports.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.



6. INSTALL REAR SEATBACK LOCK COVER


    B271143
  1. Engage the guide and install the rear seatback lock cover.

  1. Tighten the screw.



7. INSTALL REAR SEAT SHOULDER BELT COVER


    B267855
  1. Engage the 4 claws and install the rear seat shoulder belt cover.



8. INSTALL SHOULDER BELT ANCHOR COVER


    B267854
  1. Engage the 2 claws and 2 hooks and install the shoulder belt anchor cover.



9. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



10. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



11. INSTALL REAR SEATBACK ASSEMBLY


    B130750E01
  1. Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.



    B135128E02
  1. Install the rear seat inner belt into the rear seatback holder.
    Text in Illustration 
    *a
    Convex

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.



12. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY
  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.