Home › BODY › EXTERIOR › NAME PLATE

NAME PLATE > INSTALLATION

for Preparation Click here



1. INSTALL REAR NAME PLATE


    B134748E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the rear name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Align the 2 pins and install a new rear name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    49 mm (1.929 in.)
    b
    56.7 mm (2.232 in.)

    NOTICE:
    Install the rear name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the rear name plate up to 20 to 30°C (68 to 86°F) and install the rear name plate.



2. INSTALL NO. 2 BACK DOOR NAME PLATE


    B134745E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 back door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    37 mm (1.457 in.)
    b
    14.5 mm (0.571 in.)

    NOTICE:
    Install the back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.



3. INSTALL NO. 1 BACK DOOR NAME PLATE


    B134742E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 back door name plate while any double-sided adhesive tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 1 back door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    28.4 mm (1.118 in.)
    b
    11.5 mm (0.453 in.)

    NOTICE:
    Install the No. 1 back door name plate in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 back door name plate up to 20 to 30°C (68 to 86°F) and install the No. 1 back door name plate.