ROOF DRIP SIDE FINISH MOULDING > INSTALLATION |
| 1. INSTALL ROOF SIDE GARNISH PROTECTOR |
Install a new roof side garnish protector with the 4 clips.
| 2. INSTALL FRONT PILLAR OUTER GARNISH |
Engage the 5 clips and install the front pillar outer garnish.
Tighten the nut.
| 3. INSTALL FRONT PILLAR GARNISH |
| 4. INSTALL ASSIST GRIP ASSEMBLY |
| 5. INSTALL ASSIST GRIP PLUG |
| 6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP |
| 7. INSTALL ROOF DRIP SIDE FINISH MOULDING RETAINER |
Install the roof drip side finish moulding retainer.
| 8. INSTALL WINDSHIELD OUTSIDE UPPER MOULDING SUB-ASSEMBLY |
Clean the windshield glass.
Using a scraper, remove the adhesive from the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Using a brush or sponge, apply Primer G to the contact surface.
Apply adhesive.
Cut the tip off the cartridge nozzle.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to a new windshield outside upper moulding, as shown in the illustration.

| Area | Measurement |
| *1 | 10 mm (0.394 in.) or more |
| *2 | 8 mm (0.315 in.) or more |
| *3 | 3.5 to 9.5 mm (0.138 to 0.374 in.) |
Engage the 4 claws and the 2 clips and install a new windshield outside upper moulding.
| Temperature | Minimum time prior to driving vehicle |
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hour |
| 5°C (41°F) | 24 hours |
Remove the protective tape.
| 9. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP |
![]() |
Clean the vehicle body.
Using an industrial dryer, heat the tape remaining on the painted surface to soften it and peel it off with a bamboo scraper.
Clean the surface using a shop rag or piece of cloth soaked in a non-residue solvent.
Apply adhesive.
Load an adhesive cartridge into an adhesive coating gun.
Remove the cap from the adhesive cartridge and pull the lever of the gun. Make sure that the adhesive comes out of the nozzle tip ( 2 outlets) uniformly. (Confirm by applying adhesive to cardboard)
Pull the lever again and apply adhesive to a part of the cardboard where it has not been applied before.
Using a paddle, mix the adhesive 10 times.
Apply the adhesive, with a uniform thickness of 0.5 mm (0.02 in.), to the surface of the hardening tape on the clip.
Set the clip in the predetermined position on the pillar and press in until extra adhesive protrudes beyond the sides of the tape (20 N (2kgf, 4.4 lb) x 2 seconds).
| Area | Measurement |
| *1 | 2.5 to 3.5 mm (0.098 to 0.138 in.) |
| *2 | 2 to 3 mm (0.079 to 0.118 in.) |
| *3 | Location Mark |
After pressing the clip, leave it for the predetermined time shown below and then install the moulding.
| Temperature | Leaving times |
| 5 to 10°C (41 to 50°F) | 1 hour or more |
| 10 to 15°C (50 to 59°F) | 30 minutes or more |
| 15 to 23°C (59 to 73°F) | 30 minutes or more |
| 23°C (73°F) or more | 15 minutes or more |
| 10. INSTALL NO. 4 ROOF DRIP SIDE FINISH MOULDING |
![]() |
Engage the clip and install the No. 4 roof drip side finish moulding.
| 11. INSTALL NO. 3 ROOF DRIP SIDE FINISH MOULDING |
![]() |
Install the No. 3 roof drip side finish moulding as shown in the illustration.
| *1 | Location Mark |
| 12. INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING |
![]() |
Install the No. 2 roof drip side finish moulding as shown in the illustration.
| *1 | Location Mark |
| 13. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING |
![]() |
Engage the clip and install the No. 1 roof drip side finish moulding.
| 14. INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT COVER |
![]() |
| *1 | Arrow Mark |
Engage the 2 claws and install the roof drip moulding joint cover.