Home › BODY › EXTERIOR › SIDE MOULDING

SIDE MOULDING > REMOVAL

for Preparation Click here


HINT:
The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. REMOVE RADIATOR GRILLE


    B134729
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 2 screws.

  1. Disengage the 5 clips and remove the radiator grille.



2. REMOVE FRONT BUMPER COVER


    B134730E02
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    B138606
  1. Using a clip remover, remove the 5 clips.



    B134731
  1. Remove the 8 screws and the 4 bolts.



    B134733
  1. Disengage the 2 claws and remove the front bumper cover.



3. REMOVE REAR BUMPER COVER


    B135140E02
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape



    B135141
  1. Remove the 7 bolts and the 2 screws.



    B268275
  1. Disengage the clamp and disconnect the floor wire.

  1. Disconnect the connector.

    HINT:
    If the vehicle is equipped with back sonar, disconnect the connector and floor wire.



    B135143
  1. Disengage the 6 claws and the 2 clips and remove the rear bumper cover.



4. REMOVE FRONT FENDER MUDGUARD


    B135082
  1. Using a clip remover, remove the clip.

  1. Remove the 5 screws and the front fender mudguard.



5. REMOVE QUARTER PANEL MUDGUARD


    B135084
  1. Using a clip remover, remove the clip.

  1. Remove the 4 screws and the quarter panel mudguard.



6. REMOVE FRONT BUMPER SIDE SUPPORT


    B134734
  1. Remove the 2 screws.

  1. Disengage the 2 claws and remove the front bumper side support LH.



7. REMOVE SIDE STEP SUB-ASSEMBLY (w/ Side Step)


    B135176
  1. Remove the 6 bolts and the side step.



8. REMOVE ROCKER PANEL MOULDING
  1. Apply protective tape to the quarter panel in the area around the rocker panel moulding.



  1. Using a clip remover, remove the 6 retainers.


    B135051E02


    Text in Illustration 
    *a
    Protective Tape
    -
    -

  1. Remove the 3 screws.



  1. Disengage the 3 clips, the 2 claws and the 5 guides, and remove the rocker panel moulding.


    B340132



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



9. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY


    B135055E02
  1. Apply protective tape to the fender panel in the area around the front fender moulding sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



    B135056
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 5 screws.



    B135057
  1. Disengage the 2 clips and remove the front fender moulding sub-assembly.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



10. REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY


    B135061E02
  1. Apply protective tape to the quarter panel in the area around the quarter outside moulding sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



    B135062
  1. Using a clip remover, remove the clip.

  1. Remove the 8 screws.



    B135063
  1. Disengage the 2 clips and remove the quarter outside moulding sub-assembly.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



11. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY


    B135016E02
  1. Apply protective tape to the front door panel in the area around the front door outside moulding sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the 2 nuts.



    B135017
  1. Using a moulding remover, disengage the 9 clips and remove the front door outside moulding sub-assembly.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



12. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY


    B340119E01
  1. Apply protective tape to the rear door panel in the area around the rear door outside moulding sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the nut.

  1. Using an infrared light, heat the vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    CAUTION:
    Do not burn yourself on the hot vehicle body or with the infrared light.

    NOTICE:
    1. Do not heat the vehicle body excessively.
    2. Remove any tape remaining on the vehicle body.



    B340118E01
  1. Using a moulding remover, while pulling the rear door outside moulding sub-assembly from the side of the vehicle, disengage the 4 clips while peeling off the double-sided tape. Then remove the rear door outside moulding sub-assembly.
    Text in Illustration 
    *a
    Double-sided Tape



13. REMOVE SPARE TIRE


14. REMOVE BACK DOOR OUTSIDE MOULDING LH


    B135025E02
  1. Apply protective tape to the back door panel in the area around the back door outside moulding LH.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the screw.



    B135026
  1. Using a moulding remover, disengage the 6 clips and remove the back door outside moulding LH.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



15. REMOVE BACK DOOR OUTSIDE MOULDING RH


    B135029E03
  1. Apply protective tape to the back door panel in the area around the back door outside moulding RH.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the screw.



    B135030
  1. Using a moulding remover, disengage the 6 clips and remove the back door outside moulding RH.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.