Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT ARMREST BASE UPPER PANEL


B135557
  1. Disengage the 3 claws and the clip.

  1. Disconnect the all connectors and remove the front armrest base upper panel.



4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)


    E148346
  1. Remove the 3 screws and the power window regulator master switch assembly.



5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)


    E148350E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the power window regulator switch assembly.
    Text in Illustration 
    *1
    Protective Tape



6. REMOVE DOOR CONTROL SWITCH (for Front Passenger Side)


    E221661E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the door control switch.
    Text in Illustration 
    *1
    Protective Tape



7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B331550E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the 2 covers.
    Text in Illustration 
    *1
    Protective Tape



    B331551
  1. Remove the 2 screws.

  1. Remove the clip.

  1. Disengage the 10 clips.



    B135572
  1. Disconnect the front door lock remote control cable and the front door inside locking cable and remove the front door trim board sub-assembly.



8. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP


    B331548
  1. Remove the front door glass inner weatherstrip from the front door trim board sub-assembly.



9. REMOVE FRONT NO. 2 DOOR SERVICE HOLE COVER


B135573
  1. Remove the 4 screws and the front No. 2 door service hole cover.



10. REMOVE OUTER REAR VIEW MIRROR

HINT:
Use the same procedure as for the LH side .



11. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



12. REMOVE FRONT NO. 1 SPEAKER


    B130580
  1. Disconnect the speaker connector.



    B130581
  1. Remove the 4 screws and the front No. 1 speaker.



13. REMOVE FRONT DOOR SERVICE HOLE COVER


B135574
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any butyl tape remaining on the door side.



14. REMOVE FRONT DOOR INSIDE PANEL PLATE


B135575
  1. Remove the 4 screws and the front door inside panel plate.



15. REMOVE FRONT DOOR CHECK ASSEMBLY


B138158
  1. Remove the 2 nuts and bolt, and then remove the front door check assembly.

    NOTICE:
    Do not drop or damage the front door check assembly when removing the bolts.

    HINT:
    Remove the front door check assembly through the service hole.



16. REMOVE FRONT DOOR GLASS RUN


B138160
  1. Remove the front door glass run.



17. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B135578
  1. Remove the hole plug.



    B138161
  1. Remove the bolt and the screw, and then remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolt and the screw.



18. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


B138162
  1. Remove the bolt and the 2 screws, and then remove the front door lower frame bracket garnish.



19. REMOVE FRONT DOOR WINDOW FRAME REAR LOWER


B331552
  1. Remove the bolt.

  1. Disengage the guide and remove the front door window frame rear lower.

    NOTICE:
    Do not drop or damage the front door window frame rear lower when removing the bolt.



20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


B135577
  1. Remove the hole plug.

  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator switch and move the front door glass sub-assembly so that the front door glass sub-assembly bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and the power window regulator switch.



    B138164
  1. Remove the 2 bolts.

  1. Pull the front door glass sub-assembly upward to remove it.

    NOTICE:
    Do not damage the front door glass sub-assembly.



21. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


B331553
  1. Disconnect the connector.

  1. Remove the 6 bolts and the front door window regulator sub-assembly.

    NOTICE:
    Do not drop or damage the front door window regulator sub-assembly.

    HINT:
    Remove the front door window regulator sub-assembly through the service hole.



22. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B135590
  1. Using "Torx" socket wrench T25, remove the 3 screws and the power window regulator motor.



23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


    B135579E01
  1. Remove the hole plug.
    Text in Illustration 
    *1
    Hole Plug

  1. Using a T30 "TORX" socket wrench, remove the screw and the front door outside handle cover with the door lock key cylinder.



    B330838E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the front door outside handle cover.
    Text in Illustration 
    *1
    Protective Tape



24. REMOVE FRONT DOOR LOCK


    B138148
  1. Using "Torx" socket wrench T30, loosen the 3 screws.

  1. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.



    B138149
  1. Disengage the 5 claws and open the cover.



    B132174
  1. Disconnect the front door lock remote control cable and the front door inside locking cable.

  1. Remove the door lock wire harness seal.



25. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


B135580
  1. Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



26. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD


B330839
  1. Disengage the 2 claws and remove the front door outside handle rear pad.



27. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD


B331557
  1. Disengage the 3 claws and remove the front door outside handle front pad.



28. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B331556
  1. Using a T30 "TORX" socket wrench, loosen the screw.



    B331554
  1. Disengage the 2 claws and the grommet.

  1. Remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.

    HINT:
    Remove the front door outside handle frame sub-assembly through the service hole.



29. REMOVE FRONT DOOR WEATHERSTRIP


B138159
  1. Disengage the 24 clips and remove the front door weatherstrip.



30. REMOVE CUSHION


B135587
  1. Remove the 2 cushions.



31. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:
Use the same procedure as for the LH side .