Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

HINT:
Use the same procedure as for the LH side .



2. INSTALL CUSHION


B135587
  1. Install the 2 cushions.



3. INSTALL FRONT DOOR WEATHERSTRIP


B138159
  1. Engage the 24 clips and install the front door weatherstrip.



4. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B331555
  1. Install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.

  1. Engage the grommet and the 2 claws.



    B331556
  1. Using a T30 "TORX" socket wrench, tighten the screw.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


B331557
  1. Engage the 3 claws and install the front door outside handle front pad.



6. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


B330839
  1. Engage the 2 claws and install the front door outside handle rear pad.



7. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


B135581
  1. Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



8. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease or dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B132174
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B138149
  1. Engage the 5 claws and close the cover.



    B132178
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.



    B138148
  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent

  1. Using "Torx" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



9. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


B330840
  1. Engage the 2 claws and install the front door outside handle cover.



    B135582E01
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the door lock key cylinder.
    Text in Illustration 
    *1
    Hole Plug

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



10. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B135590
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and the rotating areas of the front door window regulator sub-assembly.

    NOTICE:
    Do not apply MP grease to the window regulator spring.



    B331553
  1. Install the front door window regulator sub-assembly with the 6 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not drop the front door window regulator sub-assembly as it may be damaged.

  1. Connect the connector.



12. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B138164
  1. Install the front door glass sub-assembly to the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not damage the front door glass sub-assembly.



    B135577
  1. Install the hole plug.



13. INSTALL FRONT DOOR WINDOW FRAME REAR LOWER


B331552
  1. Engage the guide and install the front door window frame rear lower.

  1. Temporarily install the bolt.



14. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B138162
  1. Install the front door lower frame bracket garnish with the bolt and the 2 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



15. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B138161
  1. Install the front door frame sub-assembly front lower with the screw.

  1. Temporarily install the bolt.



16. INSTALL FRONT DOOR GLASS RUN


B138160
  1. Install the front door glass run.



    B138163
  1. Tighten the front door window frame rear lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B140037
  1. Tighten the front door frame sub-assembly front lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B135578
  1. Install the hole plug.



17. INSTALL FRONT DOOR CHECK ASSEMBLY


B138158
  1. Apply MP grease to the sliding areas of the front door check assembly.

  1. Install the front door check assembly onto the door panel with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the front door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



18. INSTALL FRONT DOOR INSIDE PANEL PLATE


B135575
  1. Install the front door inside panel plate with the 4 screws.



19. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.



    B135576E01
  1. Install a new front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover taking care to prevent wrinkles.



20. INSTALL FRONT NO. 1 SPEAKER


    B130581
  1. Install the front No. 1 speaker with the 4 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



    B130580
  1. Connect the speaker connector.



21. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



22. INSTALL OUTER REAR VIEW MIRROR

HINT:
Use the same procedure as for the LH side .



23. INSTALL FRONT NO. 2 DOOR SERVICE HOLE COVER


B135573
  1. Install the front No. 2 door service hole cover with the 4 screws.



24. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP


    B331548
  1. Install the front door glass inner weatherstrip to the front door trim board sub-assembly.



25. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B135572
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B331551
  1. Engage the 10 clips and install the front door trim board sub-assembly.

  1. Install the clip.

  1. Install the 2 screws.



    B331549
  1. Engage the 2 claws and close the 2 covers.



26. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)
  1. Install the power window regulator master switch assembly with the 3 screws.



27. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)


    E148351
  1. Engage the 2 claws and install the power window regulator switch assembly.



28. INSTALL DOOR CONTROL SWITCH (for Front Passenger Side)


    E221662
  1. Engage the 2 claws and install the door control switch.



29. INSTALL FRONT ARMREST BASE UPPER PANEL
  1. Connect the all connectors.



    B135557
  1. Engage the 3 claws and the clip and install the front armrest base upper panel.



30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).