Home › BODY › ENGINE HOOD / DOOR › BACK DOOR

BACK DOOR > DISASSEMBLY

for Preparation Click here



1. REMOVE SPARE WHEEL NO. 2 COVER (w/ Rear Monitor)


2. REMOVE SPARE WHEEL COVER (w/ Rear Monitor)


3. REMOVE SPARE WHEEL CARRIER NO. 2 BRACKET (w/ Rear Monitor)


B208354
  1. Remove the 2 bolts and remove the spare wheel carrier No. 2 bracket.

  1. Disconnect the connector.



4. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Rear Monitor)


E172220
  1. Remove the bolt and rear television camera.



5. REMOVE SPARE DISC WHEEL


6. REMOVE BACK DOOR OUTSIDE MOULDING LH


    B135025E02
  1. Apply protective tape to the back door panel in the area around the back door outside moulding LH.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the screw.



    B135026
  1. Using a moulding remover, disengage the 6 clips and remove the back door outside moulding LH.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



7. REMOVE BACK DOOR OUTSIDE MOULDING RH


    B135029E03
  1. Apply protective tape to the back door panel in the area around the back door outside moulding RH.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the screw.



    B135030
  1. Using a moulding remover, disengage the 6 clips and remove the back door outside moulding RH.



    B135058E01
  1. Turn the clips 90° clockwise and remove them.



8. REMOVE SPARE WHEEL CARRIER BRACKET SUB-ASSEMBLY


B135543
  1. Remove the 2 bolts and 2 nuts and remove the spare wheel carrier bracket.

  1. Remove the 4 spare wheel bracket pads.



9. REMOVE SPARE WHEEL CARRIER BRACKET SUB-ASSEMBLY (w/ Rear Monitor)


B208355
  1. Remove the 2 bolts and 2 nuts and remove the spare wheel carrier bracket.

  1. Remove the 4 spare wheel bracket pads.



10. REMOVE BACK DOOR TRIM COVER RH


B139381
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the back door trim cover.



11. REMOVE BACK DOOR TRIM COVER LH

HINT:
Use the same procedure as described for the RH side.



12. REMOVE DOOR TRIM RETAINER CAP


B135553
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the door trim retainer cap.



13. REMOVE BACK DOOR TRIM BOARD


B135554
  1. Remove the 2 screws.

  1. Disengage the 16 clips and remove the back door trim board.



14. REMOVE BACK DOOR SERVICE HOLE COVER


B135544
  1. Remove the back door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



15. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)


    E127888
  1. Open the rear wiper arm head cap.



    E127889
  1. Remove the nut and the rear wiper arm and blade.



16. REMOVE REAR WIPER MOTOR (w/ Rear Wiper)


    E127890
  1. Disconnect the connector.

  1. Remove 3 bolts and the rear wiper motor.



17. REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)


18. REMOVE MULTIPLEX NETWORK DOOR ECU


B135545
  1. Disconnect the 2 connectors and harness clamp.

  1. Remove the 2 screws and the multiplex network door ECU.



19. REMOVE BACK WINDOW LOCK ASSEMBLY


    B135521
  1. Disconnect the connector and clamp.

  1. Remove the 3 bolts and the back window lock.



20. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    B135112E01
  1. Apply protective tape to the back door panel in the area around the back door outside garnish.



    B135109
  1. Using a clip remover, disengage the 4 claws and remove the plug hole.



    B135110
  1. Disconnect the license light connector.

  1. Disconnect the back door lock rod.



    B135111
  1. Remove the 2 nuts.



    B135113E01
  1. Using a moulding remover, disengage the 4 clips and remove the back door outside garnish.



21. REMOVE BACK DOOR LOCK ASSEMBLY


    B135517
  1. Disconnect the back door lock rod as shown in the illustration.

  1. Disconnect the connector.



    B135519E01
  1. Loosen bolt A.

  1. Using "Torx" socket wrench T30, remove the 3 screws and the back door lock.

    NOTICE:
    Do not drop or damage the back door lock when removing the screws.

    HINT:
    Remove the back door lock through the service hole.



22. REMOVE BACK DOOR LOCK CYLINDER ASSEMBLY


B135546
  1. Disconnect the connector and the 2 clamps.



    B135548
  1. Remove the retainer and the back door lock cylinder.



23. REMOVE NO. 1 REAR SPOILER COVER


B135550
  1. Remove the 4 screws and No. 1 rear spoiler cover.



24. REMOVE REAR SPOILER


    B135162
  1. Disconnect high mounted stop light connector.

  1. Using a clip remover, remove the 3 clamps.

  1. Remove the washer hose from the claw of the rear spoiler.

  1. Disconnect the washer hose.



    B135163
  1. Remove the 4 nuts.



25. REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY


    B135165
  1. Remove the 2 screws and the high mounted stop light.



26. REMOVE BACK DOOR SIDE FEMALE STOPPER SUB-ASSEMBLY


B135549
  1. Remove the 2 bolts and back door side female stopper.



27. REMOVE BACK WINDOW SUPPORT LH


B135523
  1. Using a screwdriver with its tip wrapped in protective tape, remove the 2 stop rings and back window support.

    NOTICE:
    1. Do not touch the rod of the back window support with gloves, to avoid fibers from adhering.
    2. When foreign matter adheres to the rod, it prevents the rod from moving smoothly and reduces its holding power.

    HINT:
    Support the back door glass by hand while removing the back window support.



28. REMOVE BACK WINDOW SUPPORT RH

HINT:
Use the same procedure as described for the LH side.



29. REMOVE BACK DOOR GLASS
  1. Disconnect the 2 defogger connectors.



    B139403
  1. Remove the 2 nuts and the back door glass.



30. REMOVE BACK WINDOW STAY UPPER BRACKET RH


B139404
  1. Remove the 2 screws, the retainer and the back window stay upper bracket.



31. REMOVE BACK WINDOW STAY UPPER BRACKET LH

HINT:
Use the same procedure as described for the RH side.



32. REMOVE BACK WINDOW LOCK STRIKER ASSEMBLY


B139405
  1. Remove the 2 screws, the retainer and the back window lock striker.



33. REMOVE BACK DOOR OUTSIDE HANDLE


B139406
  1. Remove the screw and the back door outside handle.

  1. Remove the bush.



34. REMOVE BACK DOOR HINGE ASSEMBLY RH


B135998
  1. Remove the bolt and the back door hinge.



35. REMOVE BACK DOOR HINGE ASSEMBLY LH

HINT:
Use the same procedure as described for the RH side.



36. REMOVE NO. 2 BACK DOOR WEATHERSTRIP


B135591
  1. Remove the No. 2 back door weatherstrip.

    NOTICE:
    Remove any tape remaining on the door side.



37. REMOVE BACK DOOR STAY UPPER BRACKET RH


B135592
  1. Remove the bolt and the back door stay upper bracket.



38. REMOVE BACK DOOR STAY UPPER BRACKET LH


B135593
  1. Remove the bolt and the back door stay upper bracket.



39. REMOVE BACK DOOR SUPPORT


B135594
  1. Using a screwdriver with its tip wrapped in protective tape, remove the 2 stop rings and back door support.

    NOTICE:
    1. Do not touch the rod of the back door support with gloves, to avoid fibers from adhering.
    2. When foreign matter adheres to the rod, it prevents the rod from moving smoothly and reduces its holding power.



40. REMOVE BACK DOOR DAMPER STAY LOWER BRACKET


B135999
  1. Remove the 2 bolts and the back door damper stay lower bracket.



41. REMOVE NO. 1 BACK DOOR NAME PLATE


    B134740E01
  1. Apply protective tape to the back door panel in the area around the No. 1 back door name plate.

  1. Using an infrared light, heat the No. 1 back door name plate.

    CAUTION:
    Do not burn yourself with the heated back door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



    B134741E01
  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 1 back door name plate.

  1. Remove the protective tape.



42. REMOVE NO. 2 BACK DOOR NAME PLATE


    B134743E01
  1. Apply protective tape to the back door panel in the area around the No. 2 back door name plate.

  1. Using an infrared light, heat the No. 2 back door name plate.

    CAUTION:
    Do not burn yourself with the heated back door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



    B134744E01
  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 2 back door name plate.

  1. Remove the protective tape.



43. REMOVE REAR NAME PLATE


    B134746E01
  1. Apply protective tape to the back door panel in the area around the rear name plate.

  1. Using an infrared light, heat the rear name plate.

    CAUTION:
    Do not burn yourself with the heated back door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



    B134747E01
  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the rear name plate.

  1. Remove the protective tape.



44. REMOVE CUSHION
  1. Remove the 2 cushions.



45. REMOVE HOLE PLUG
  1. Remove the 2 hole plugs.