TRANSPONDER KEY ECU > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR SCUFF PLATE LH |
| 3. REMOVE FRONT FLOOR FOOTREST |
![]() |
Disengage the 4 claws and remove the front floor footrest.
| 4. REMOVE FOOTREST CLIP |
![]() |
Remove the 2 footrest clips.
| 5. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Remove the clip.
Disengage the 2 claws and remove the cowl side trim board.
| 6. REMOVE COWL SIDE TRIM BOARD LH |
| 7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the front door opening trim weatherstrip.
| 8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 9. REMOVE ASSIST GRIP PLUG |
![]() |
| *1 | Protective Tape |
| *a | for RH Side |
| *b | for LH Side |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip plug.
| 10. REMOVE ASSIST GRIP ASSEMBLY |
![]() |
| *a | for RH Side |
| *b | for LH Side |
Remove the 2 screws and the assist grip.
| 11. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Disengage the 2 clips and the guide and remove the front pillar garnish.
| 12. REMOVE FRONT PILLAR GARNISH LH |
| 13. REMOVE INSTRUMENT PANEL GARNISH LH |
![]() |
Remove screw <H>.
Disengage the 3 clips and remove the instrument panel garnish.
| 14. REMOVE INSTRUMENT PANEL GARNISH RH |
![]() |
Remove screw <H>.
Disengage the 3 clips and remove the instrument panel garnish.
| 15. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Remove the 2 <H> screws.
Disengage the 4 clips and remove the integration control panel assembly.
Disconnect the 3 connectors.
| 16. REMOVE RADIO RECEIVER ASSEMBLY |
![]() |
Remove the 4 bolts and the radio receiver.
Disconnect the connectors.
| 17. REMOVE PARKING BRAKE HOLE COVER SUB-ASSEMBLY |
![]() |
Disengage the 2 A claws and 2 B claws.
Slide the parking brake hole cover toward the front of the vehicle, disengage the 2 C claws and remove the parking brake hole cover.
| 18. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission) |
![]() |
Remove the shift lever knob.
| 19. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD) |
![]() |
Remove the shift lever knob.
| 20. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY |
![]() |
Shift the shift lever into the N position.
Disengage the 5 clips and 3 claws and remove the console upper rear panel.
| 21. REMOVE BOX BOTTOM MAT |
![]() |
Remove the box bottom mat.
| 22. REMOVE FRONT CONSOLE BOX |
![]() |
Remove the 4 <D> bolts.
Disengage the 5 claws and remove the console box.
| 23. REMOVE CONSOLE UPPER PANEL NO. 1 GARNISH |
![]() |
Disengage claw A and the clip.
Slide the console upper panel garnish toward the rear of the vehicle, disengage the claw B and remove the console upper panel garnish.
| 24. REMOVE INSTRUMENT LOWER COVER SUB-ASSEMBLY |
![]() |
Remove the 2 clips and 2 <F> bolts.
Disengage the 3 clips and 2 claws and remove the instrument lower cover.
| 25. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Disengage the 4 clips and 2 claws and remove the instrument panel register.
| 26. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and separate the hood lock control lever.
| 27. REMOVE INSTRUMENT PANEL FINISH PLATE |
![]() |
Using a screwdriver with its tip wrapped in protective tape, remove the instrument panel finish plate.
| 28. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Remove the 2 <F> bolts.
Disengage the 5 clips and claw and remove the lower instrument panel finish panel.
Disconnect the connector.
| 29. REMOVE LOWER INSTRUMENT PANEL LH |
![]() |
Remove the 4 <F> bolts and remove the lower instrument panel.
| 30. REMOVE INSTRUMENT CLUSTER LOWER FINISH PANEL |
![]() |
Disengage the 3 clips and the 4 claws and remove the instrument cluster finish panel.
Disconnect the connectors.
| 31. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws.
![]() |
Disconnect the 2 connectors and clamp and remove the combination meter.
| 32. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Disengage the claw and separate the glove compartment door stoppers from the glove compartment door.
Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.
![]() |
Pull the glove compartment door assembly toward the rear of the vehicle to release the 3 hinges and remove the glove compartment door assembly.
| 33. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Remove screw <A>.
Disengage the 2 clips and claw and remove the instrument panel lower finish panel.
Separate the connectors from the instrument panel lower finish panel.
| 34. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Apply protective tape, as shown in the illustration.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the instrument panel hole cover.
![]() |
Remove the bolt <F> and clip.
Disengage the 4 clips and 2 claws and remove the instrument panel register.
| 35. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Disengage the 4 clips and claw and remove the instrument panel speaker panel.
| 36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
| 37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Remove the 2 bolts and the front speaker.
Disconnect the speaker connector.
| 38. REMOVE ASSIST GRIP RETAINER RH |
![]() |
Remove the 2 bolts and remove the assist grip retainer.
| 39. REMOVE ASSIST GRIP RETAINER LH |
| 40. DISCONNECT PASSENGER AIRBAG CONNECTOR |
![]() |
Slide the slider and disconnect the passenger airbag connector.
| 41. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
Disengage the clamps and disconnect the connectors.
Remove the 2 <C> bolts, 2 <E> bolts, 7 <F> bolts and nut <G> and remove the instrument panel.

| 42. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
Disengage the 3 claws and remove the instrument panel finish panel end.
| 43. REMOVE TRANSPONDER KEY BRACKET (w/ Bracket) |
![]() |
Remove the 2 clips.
Remove the 2 nuts and remove the transponder key bracket.
| 44. REMOVE TRANSPONDER KEY ECU |
Disconnect the connector.
![]() |
Remove the nut and remove the transponder key ECU.