Home › BODY ELECTRICAL › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a door lock that has been removed, replace the packing in the connecting part with new.
  2. Make sure that no grease or dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B132174
  1. Connect the front door lock remote control cable and the front door inside locking cable.



    B138149
  1. Engage the 5 claws and close the cover.



    B132178
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.



    B138148
  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent

  1. Using "Torx" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY


B135582
  1. Using a "Torx" socket wrench T30, install the front door lock cylinder.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B138164
  1. Install the front door glass sub-assembly to the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Do not damage the front door glass sub-assembly.



    B135577
  1. Install the hole plug.



4. INSTALL FRONT DOOR WINDOW FRAME REAR LOWER


B331552
  1. Engage the guide and install the front door window frame rear lower.

  1. Temporarily install the bolt.



5. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B138162
  1. Install the front door lower frame bracket garnish with the bolt and the 2 screws.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



6. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B138161
  1. Install the front door frame sub-assembly front lower with the screw.

  1. Temporarily install the bolt.



7. INSTALL FRONT DOOR GLASS RUN


B138160
  1. Install the front door glass run.



    B138163
  1. Tighten the front door window frame rear lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B140037
  1. Tighten the front door frame sub-assembly front lower to the specified torque with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B135578
  1. Install the hole plug.



8. INSTALL FRONT DOOR WEATHERSTRIP


B138159
  1. Engage the 24 clips and install the front door weatherstrip.



9. INSTALL FRONT DOOR CHECK ASSEMBLY


B138158
  1. Apply MP grease to the sliding areas of the front door check assembly.

  1. Install the front door check assembly onto the door panel with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the front door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. INSTALL FRONT DOOR INSIDE PANEL PLATE


B135575
  1. Install the front door inside panel plate with the 4 screws.



11. INSTALL FRONT DOOR SERVICE HOLE COVER


B135574
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any butyl tape remaining on the door side.



12. INSTALL FRONT NO. 1 SPEAKER


    B130581
  1. Install the front No. 1 speaker with the 4 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }



    B130580
  1. Connect the speaker connector.



13. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B135101
  1. Engage the 8 claws and install a new front door glass outer weatherstrip.



    B135099E01
  1. Remove the protective tape.



14. INSTALL OUTER REAR VIEW MIRROR


B138151
  1. Engage the 2 claws on the upper side of the mirror and the 6 clips and install the mirror.

    HINT:
    Heating the mirror holder with a domestic dryer before this procedure makes the work easier.



    B135564
  1. Install the outer rear view mirror with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



15. INSTALL FRONT NO. 2 DOOR SERVICE HOLE COVER


B135573
  1. Install the front No. 2 door service hole cover with the 4 screws.



16. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B135572
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B331551
  1. Engage the 10 clips and install the front door trim board sub-assembly.

  1. Install the clip.

  1. Install the 2 screws.



    B331549
  1. Engage the 2 claws and close the 2 covers.



17. INSTALL FRONT ARMREST BASE UPPER PANEL
  1. Connect the all connectors.



    B135557
  1. Engage the 3 claws and the clip and install the front armrest base upper panel.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }