Home › ENGINE › 1GR-FE COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. REMOVE V-BANK COVER


    A229925E02
  1. Raise the front of the V-bank cover to disengage the 2 pins.
    Text in Illustration 
    *1
    Pin
    *2
    Hook
    *3
    No. 1 V-bank Cover Bracket

  1. Disengage the 2 hooks and remove the V-bank cover from the No. 1 V-bank cover bracket.



2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts from the No. 1 engine under cover sub-assembly.



    A224743E01
  1. Unhook the No. 1 engine under cover sub-assembly from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.



    A070279E03
  1. Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape



  1. Fix the vinyl hose with tape.


    A307922E01


    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.



4. REMOVE UPPER RADIATOR SUPPORT SEAL


    A226630
  1. Disengage the 7 clips and remove the upper radiator support seal from the fan shroud.



5. REMOVE FAN SHROUD (for Automatic Transmission)


    A289174
  1. Disconnect the radiator reserve tank hose from the radiator assembly.



    A226632
  1. Loosen the 4 nuts holding the fan and fluid coupling assembly.



    A217571
  1. While turning the V-ribbed belt tensioner assembly counterclockwise, align the service hole for the V-ribbed belt tensioner assembly and the V-ribbed belt tensioner assembly fixing position, and then insert a bar of φ 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner assembly in place.

    HINT:
    The pulley bolt for the V-ribbed belt tensioner assembly has a left-hand thread.

  1. Remove the fan and generator V belt.



    A287966E01
  1. Disengage the clamp and disconnect the 2 oil cooler hoses from the hose clamp.
    Text in Illustration 
    *1
    Oil Cooler Hose

  1. Remove the bolt and separate the radiator reserve tank assembly from the radiator assembly.

  1. Remove the 2 bolts and separate the fan shroud from the radiator assembly.

  1. Disengage the 2 guides of the fan shroud from the radiator assembly as shown in the illustration.

  1. Remove the 4 nuts of the fan and fluid coupling assembly, and then remove the fan shroud together with the fan and fluid coupling assembly.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump assembly.



6. REMOVE FAN SHROUD (for Manual Transmission)


    A289174
  1. Disconnect the radiator reserve tank hose from the radiator assembly.



    A226632
  1. Loosen the 4 nuts holding the fan and fluid coupling assembly.



    A217571
  1. While turning the V-ribbed belt tensioner assembly counterclockwise, align the service hole for the V-ribbed belt tensioner assembly and the V-ribbed belt tensioner assembly fixing position, and then insert a bar of φ 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner assembly in place.

    HINT:
    The pulley bolt for the V-ribbed belt tensioner assembly has a left-hand thread.

  1. Remove the fan and generator V belt.



    A289102
  1. Remove the bolt and separate the radiator reserve tank assembly from the radiator assembly.

  1. Remove the 2 bolts and separate the fan shroud from the radiator assembly.

  1. Disengage the 2 guides of the fan shroud from the radiator assembly as shown in the illustration.

  1. Remove the 4 nuts of the fan and fluid coupling assembly, and then remove the fan shroud together with the fan and fluid coupling assembly.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump assembly.



7. REMOVE RADIATOR GRILLE


    B134729
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 2 screws.

  1. Disengage the 5 clips and remove the radiator grille.



8. DISCONNECT NO. 1 RADIATOR HOSE (w/ Secondary Air Injection System)


    A287963
  1. Remove the hose clamp from the No. 1 radiator hose and the No. 1 air injection system hose.

  1. Loosen the hose clip and disconnect the No. 1 radiator hose from the water inlet housing.



9. DISCONNECT NO. 1 RADIATOR HOSE (w/o Secondary Air Injection System)


    A226635
  1. Loosen the hose clip and disconnect the No. 1 radiator hose from the water inlet housing.



10. DISCONNECT NO. 2 RADIATOR HOSE


    A226636
  1. Loosen the hose clip and disconnect the No. 2 radiator hose from the water inlet with thermostat.



11. DISCONNECT OIL COOLER HOSE (for Automatic Transmission)


    A226646
  1. Loosen the 2 hose clips and disconnect the 2 oil cooler hoses from the radiator assembly.



12. REMOVE RADIATOR ASSEMBLY


  1. Remove the 4 bolts, and the radiator assembly from the vehicle.


    A129886



13. REMOVE NO. 1 RADIATOR HOSE


    A226640
  1. Loosen the hose clip and remove the No. 1 radiator hose from the radiator assembly.



14. REMOVE NO. 2 RADIATOR HOSE


    A226639
  1. Loosen the hose clip and remove the No. 2 radiator hose from the radiator assembly.



15. REMOVE NO. 1 RADIATOR SUPPORT BUSH


    A287967E01
  1. Remove the 2 No. 1 radiator supports, 2 No. 2 radiator supports and 4 No. 1 radiator support bushes from the radiator assembly.
    Text in Illustration 
    *1
    No. 1 Radiator Support Bush
    *2
    No. 1 Radiator Support
    *3
    No. 2 Radiator Support



16. REMOVE RADIATOR DRAIN COCK SUB-ASSEMBLY
  1. Remove the radiator drain cock sub-assembly from the radiator assembly.

    HINT:
    Replace the O-ring if it is damaged.