Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY


    F043315E01
  1. Remove the bolt and separate the steering shaft thrust stopper from the steering intermediate shaft assembly.

  1. Mark matchmarks on the steering column assembly and steering intermediate shaft.

  1. Pull out the intermediate shaft assembly and steering shaft thrust stopper from the steering column assembly.



2. REMOVE STEERING COLUMN UPPER CLAMP


    C090693E01
  1. Using a 3 mm (0.12 in.) pin punch, mark the center of the 2 tapered-head bolts.

  1. Using a 3 to 4 mm (0.12 - 0.16 in.) drill, drill into the 2 bolts.

  1. Using a screw extractor, remove the 2 tapered-head bolts, steering column bracket assembly upper and steering column upper clamp.



3. REMOVE STEERING MAIN SHAFT ASSEMBLY


    H041540E01
  1. Using SST, remove the 2 tension springs.

    SST
    09921-00010  



    F043308E01
  1. Remove the 2 bolts and steering column protector.



    F043307E01
  1. Using SST, remove the tension spring.

    SST
    09921-00010  

  1. Remove the 2 bolts and the turn signal bracket.



    C090875E01
  1. Using a 6 mm hexagon wrench, remove the 2 tilt steering bolts.

  1. Pull out the main shaft with the steering column tube sub-assembly upper from the column tube.



    C090846
  1. Bend the joint of the main shaft at right angles, and leaving the cross ball in the No. 2 main shaft sub-assembly, divide the main shaft into the No. 1 main shaft with the steering column tube sub-assembly upper and the No. 2 main shaft sub-assembly.



    H041541E01
  1. Secure the No. 1 main shaft with the steering column tube sub-assembly upper and SST in a vise.

    SST
    09316-60011   (09316-00051)



    H041542E01
  1. Using SST, compress the spring of the steering column tube sub-assembly upper.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09958-04011)

    NOTICE:
    Do not overtighten SST.



    H041543
  1. Using a snap ring expander, remove the snap ring and No. 1 main shaft.

  1. Remove the compression spring, bearing thrust collar and bearing from the No. 1 main shaft.



4. REMOVE TRANSPONDER KEY AMPLIFIER

NOTICE:
Take care not to use excessive force to prevent the case from being damaged.

  1. Expand the claw hung on the upper bracket by approx. 1.0 mm (0.039 in.) using a screwdriver.



    F008822
  1. Pull the transponder key amplifier toward the rear of the vehicle with the claw open.



5. REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY


    C082969E01
  1. Turn the ignition switch lock cylinder assembly in the ACC position.

  1. Push down the stop pin with a screwdriver and pull out the ignition switch lock cylinder assembly.



6. REMOVE UN-LOCK WARNING SWITCH ASSEMBLY


    F043296
  1. Disconnect the un-lock warning switch assembly connector from the ignition or starter switch assembly.

  1. Remove the un-lock warning switch assembly toward the rear of the vehicle by pushing up the center part.



7. REMOVE IGNITION OR STARTER SWITCH ASSEMBLY


    F043313
  1. Remove the 2 screws and ignition or starter switch assembly from the steering column bracket assembly upper.



8. REMOVE KEY INTER LOCK SOLENOID (for Automatic Transmission)


    F043314
  1. Remove the 2 screws and key inter lock solenoid from the steering column bracket assembly upper.