Home › DRIVE LINE ยท PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY

FRONT PROPELLER SHAFT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT PROPELLER SHAFT UNIVERSAL JOINT SPIDER KIT


Z004248
  1. Apply MP grease to a new spider and spider bearings.

  1. Fit the spider into the flange yoke.



    C063061E02
  1. Using SST, install the spider bearings onto the spider.

    SST
    09332-25010  

  1. Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal in width.

    SST
    09332-25010  



    G020755
  1. Install 4 new snap rings of equal thickness which will allow no axial play.

    HINT:
    Do not reuse the snap rings.

    Thickness of snap ring 
    Parts No.
    Thickness mm (in.)
    Mark
    90520-25039
    2.28 to 2.30
    1
    90520-25040
    2.30 to 2.32
    2
    90520-25041
    2.32 to 2.34
    -
    90520-25042
    2.34 to 2.36
    Brown
    90520-25043
    2.36 to 2.38
    Blue
    90520-25044
    2.38 to 2.40
    6
    90520-25045
    2.40 to 2.42
    7
    90520-25046
    2.42 to 2.44
    8
    90520-25047
    2.44 to 2.46
    C116318
    90520-25048
    2.46 to 2.48
    10
    90520-25049
    2.48 to 2.50
    A
    90520-25050
    2.50 to 2.52
    B
    90520-25051
    2.52 to 2.54
    C
    90520-25052
    2.54 to 2.56
    D
    90520-25053
    2.56 to 2.58
    E
    90520-25054
    2.18 to 2.20
    J
    90520-25055
    2.20 to 2.22
    K
    90520-25056
    2.22 to 2.24
    F
    90520-25057
    2.24 to 2.26
    G
    90520-25058
    2.26 to 2.28
    H

    NOTICE:
    1. Use a new snap ring.
    2. Use snap rings as close as possible to the same thickness on both ends.



    G022297E02
  1. Using a hammer, tap the yoke until there is no clearance between the spider bearing outer race and the snap ring.

    HINT:
    Install a new spider bearing on the sleeve side in the procedure described above.

  1. Align the matchmarks on the flange yoke and the sleeve yoke.



    F044258E01
  1. Using SST, install the spider bearings onto the spider.

    SST
    09332-25010  

  1. Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal in width.

    SST
    09332-25010  

  1. Install 4 new snap rings of equal thickness which will allow no axial play.

    HINT:
    Do not reuse the snap rings.

    Thickness of snap ring 
    Parts No.
    Thickness mm (in.)
    Mark
    90520-25039
    2.28 to 2.30
    1
    90520-25040
    2.30 to 2.32
    2
    90520-25041
    2.32 to 2.34
    -
    90520-25042
    2.34 to 2.36
    Brown
    90520-25043
    2.36 to 2.38
    Blue
    90520-25044
    2.38 to 2.40
    6
    90520-25045
    2.40 to 2.42
    7
    90520-25046
    2.42 to 2.44
    8
    90520-25047
    2.44 to 2.46
    C116318
    90520-25048
    2.46 to 2.48
    10
    90520-25049
    2.48 to 2.50
    A
    90520-25050
    2.50 to 2.52
    B
    90520-25051
    2.52 to 2.54
    C
    90520-25052
    2.54 to 2.56
    D
    90520-25053
    2.56 to 2.58
    E
    90520-25054
    2.18 to 2.20
    J
    90520-25055
    2.20 to 2.22
    K
    90520-25056
    2.22 to 2.24
    F
    90520-25057
    2.24 to 2.26
    G
    90520-25058
    2.26 to 2.28
    H

    NOTICE:
    1. Use a new snap ring.
    2. Use snap rings as close as possible to the same thickness on both ends.



    G022298E01
  1. Using a plastic hammer, tap the yoke until there is no clearance between the spider bearing outer race and the snap ring.

    HINT:
    Install a new spider bearing on the sleeve side in the procedure described above.



2. INSPECT UNIVERSAL JOINT SPIDER BEARING
  1. Check that the joints move smoothly.

  1. Check the spider bearing axial play by turning the yoke while holding the shaft tightly.

    Maximum bearing axial play:
    0 mm (0 in.)



3. INSPECT FRONT PROPELLER SHAFT ASSEMBLY


HINT:
When replacing the spider bearing, be sure that the grease fitting hole is facing in the direction shown in the illustration.



C098696E02