Home › DRIVE LINE ยท VF4B TRANSFER › TRANSFER CASE OIL SEAL

TRANSFER CASE OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.



    F043487E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.

    SST
    09316-60011   (09316-00011)



2. REMOVE TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL


F043517E01
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.

  1. Coat the lip of the oil seal with MP grease.



3. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


F044048E02
  1. Apply gear oil to the connecting areas of the companion flange and driven sprocket.

  1. Install the companion flange onto the driven sprocket.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }



    F050151E01
  1. Using a chisel and hammer, stake the lock nut to the driven sprocket.

    NOTICE:
    1. Securely stake the shaft to the lock nut's groove.
    2. Be careful not to damage parts around the lock nut.
    3. Do not apply excessive force to the shaft.



4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


C098708E04
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4bolts and 4 washers.



    C098709E03
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and the propeller shaft assembly.



5. INSTALL LOWER TRANSFER CASE PROTECTOR


C133827
  1. Install the protector with the 5 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }

  1. Install the brake hose clamp.



6. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



7. CHECK FOR TRANSFER OIL LEAKAGE
  1. Remove the case plug (for filler) and gasket.



    C083746E01
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil type :
    Toyota Genuine Transfer Gear Oil LF or equivalent

    Viscosity:
    SAE 75W

    Standard capacity:
    1.4 liter (1.5 US qts, 1.3 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }