Home › DRIVE LINE ยท VF4B TRANSFER › EXTENSION HOUSING OIL SEAL

EXTENSION HOUSING OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL EXTENSION HOUSING OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.



    F043486E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the housing upper surface.

    SST
    09316-60011   (09316-00011)



2. INSTALL TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using SST and a hammer, tap in a new oil seal (for rear) in the same way as the oil seal (for front).

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the companion flange.

  1. Coat the lip of the oil seal with MP grease.



3. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Apply gear oil to the connecting area of the companion flange and output shaft.

  1. Install the companion flange onto the output shaft.

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)

    Torque:
    118 N*m{ 1,203 kgf*cm , 87 ft.*lbf }



4. INSTALL REAR PROPELLER SHAFT ASSEMBLY


C098700E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098699E02
  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



5. INSTALL LOWER TRANSFER CASE PROTECTOR


C133827
  1. Install the protector with the 5 bolts.

    Torque:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }

  1. Install the brake hose clamp.



6. ADD TRANSFER OIL
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



7. CHECK FOR TRANSFER OIL LEAKAGE
  1. Remove the case plug (for filler) and gasket.



    C083746E01
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil type :
    Toyota Genuine Transfer Gear Oil LF or equivalent

    Viscosity:
    SAE 75W

    Standard capacity:
    1.4 liter (1.5 US qts, 1.3 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }