Home › DRIVE LINE ยท DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL

FRONT DIFFERENTIAL CARRIER OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


C093595E01
  1. Install a new bearing spacer.

    HINT:
    Install the spacer in the correct direction.



2. INSTALL FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.



3. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


G021735E01
  1. Using SST and a hammer, install the roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).



4. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


5. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


F040719E03
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-22010  

    Oil seal depth:
    3.9 to 4.8 mm (0.154 to 0.188 in.)



6. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F040716E01
  1. Using SST, instal the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Using SST to hold the companion flange, install the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3,770 kgf*cm , 273 ft.*lbf } or less



7. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C089308E01
  1. Using a torque wrench, measure the preload.

    Preload (at starting):
    Item
    Specified Condition
    New bearing
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Used bearing
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If the result is not as specified, adjust the preload.



8. STAKE FRONT DRIVE PINION COMPANION FLANGE NUT


C089310E01
  1. Using a chisel and hammer, stake the nut.



9. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


    C098708E04
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



    C098709E03
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



10. ADD DIFFERENTIAL OIL


D025304E05
  1. Stop the vehicle on a level surface.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    1. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Differential oil type and viscosity:
    Toyota Genuine Differential gear oil LT 75W-85 API GL-5 SAE 75W-85 or equivalent


    Differential Oil Capacity:

    Item
    Capacity
    Front Differential
    w/o A.D.D.
    1.35 to 1.45 Liters
    (1.43 to 1.53 US qts, 1.19 to 1.28 Imp qts.)
    w/ A.D.D.
    1.50 to 1.60 Liters
    (1.59 to 1.69 US qts, 1.32 to 1.41 Imp qts.)
    Rear Differential
    w/o Differential Lock
    2.45 to 2.55 Liters
    (2.59 to 2.69 US qts, 2.16 to 2.24 Imp qts.)
    w/ Differential Lock
    2.40 to 2.50 Liters
    (2.54 to 2.64 US qts, 2.11 to 2.20 Imp qts.)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug with a new gasket.

    Torque:
    Front differential:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }
    Rear differential:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



11. CHECK FOR DIFFERENTIAL OIL LEAKAGE


12. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the rear engine under cover with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



13. INSTALL NO. 1 ENGINE UNDER COVER
  1. Hook the No. 1 engine under cover sub-assembly to the frame.

  1. Install the 4 bolts to the No. 1 engine under cover sub-assembly.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }