Home › BRAKE › BRAKE › REAR BRAKE FLEXIBLE HOSE

REAR BRAKE FLEXIBLE HOSE > INSTALLATION

for Preparation Click here



1. INSTALL REAR FLEXIBLE HOSE


C168986E01
  1. Install the flexible hose with a new clip.

  1. Using a union nut wrench, install the brake tube onto the flexible hose while holding the flexible hose with a wrench.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.

  1. Install the flexible hose onto the disc brake cylinder with the union bolt and a new gasket.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



2. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE


C168987E01
  1. Install the flexible hose with 2 new clips.

  1. Using a union nut wrench, install the brake tubes onto the flexible hose while holding the flexible hose with a wrench.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 144 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a union nut wrench with a fulcrum length of 22 mm (0.866 in.) (Click here).
    2. This torque value is effective when the union nut wrench is parallel to a torque wrench.



3. BLEED BRAKE LINE
  1. Turn the ignition switch on (IG).

  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.

  1. Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.

  1. Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.

  1. With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.

    HINT:
    1. Air is bled as the pump motor operates while the brake pedal is being depressed.
    2. Be sure to release the brake pedal to stop the motor after approximately 100 seconds of continuous operation.
    3. As brake fluid is continuously drained while the pump operates, it is not necessary to repeatedly depress the brake pedal.

  1. When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.

  1. Turn the ignition switch off (IG).

  1. Inspect for brake fluid leaks.

  1. Check and adjust the brake fluid level .



4. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }