Home › BODY ELECTRICAL › LIGHTING › REAR COMBINATION LIGHT ASSEMBLY

REAR COMBINATION LIGHT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR COMBINATION LIGHT ASSEMBLY
  1. Connect the 3 connectors to install the rear combination light assembly.

  1. Install the 3 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Install the 3 screws.

  1. Install the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Engage the 6 clips and the 8 claws and install the deck trim side panel.

  1. Install the 3 screws.



4. INSTALL REAR DECK TRIM COVER (w/ Power Outlet Socket)
(Click here)


5. CONNECT REAR SEAT OUTER BELT ASSEMBLY

HINT:
Use the same procedure as for the RH side.



6. INSTALL LAP BELT OUTER ANCHOR COVER

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the lap belt outer anchor cover.



7. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)


    B134990
  1. Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Connect the speaker connector.



8. INSTALL SPEAKER MOUNTING COVER (w/ Woofer)


    B134991
  1. Engage the 8 clips and install the speaker mounting cover.



9. INSTALL DECK SIDE GARNISH (w/ Woofer)


    B134992
  1. Engage the 6 claws and install the deck side garnish.



10. INSTALL QUARTER TRIM POCKET (w/o Woofer)


    B130613
  1. Engage the 6 claws and install the quarter trim pocket.



11. INSTALL SIDE TRIM COVER (w/o Woofer)


    B130612
  1. Engage the 8 claws and install the side trim cover.



12. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)


    B130611
  1. Engage the 7 claws and install the quarter trim pocket tray.



13. INSTALL PACKAGE HOLDER NET HOOK

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }



14. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    B130604E02
  1. Align the locating marks with the paint marks first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Text in Illustration 
    *a
    Locating Mark
    *b
    Paint Mark

    Paint mark:
    Area
    Color
    RH side
    White
    LH side
    Red



15. INSTALL REAR DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.



16. INSTALL FRONT DOOR SCUFF PLATE

HINT:
Use the same procedure as for the RH side.



17. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


B179163E01

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.



18. INSTALL REAR FLOOR MAT ASSEMBLY


    B130594
  1. Install the rear floor mat with the 2 clips.



19. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B130593
  1. Engage the 11 claws and install the rear floor mat support plate.



    B130592
  1. Tighten the 5 screws.



20. INSTALL REAR FLOOR BOARD


    B135075
  1. Engage the clip and claw and install the rear floor board.



    B135074E02
  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.



21. INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)


    B130750E01
  1. Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Pull up the rear seatback.



    B135128E02
  1. Install the rear seat inner belt into the rear seatback holder.
    Text in Illustration 
    *a
    Convex

  1. Install the anchor plate of the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat inner belt.



22. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH (for RH Side)
  1. Pull the rear seatback lock release button and tilt the rear seatback forward.

  1. Engage the 10 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.



23. INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)


    B130721E01
  1. Engage the hook and temporarily install the rear seatback with the 2 bolts.

  1. Tighten the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Install the rear center seat inner belt into the rear seatback holder.



24. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH (for LH Side)
  1. Engage the 8 clips and install the rear seatback board carpet.

  1. Pull up the rear seatback.