Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CABLE CLAMP
  1. Install the parking brake cable clamp onto the parking brake cable.



2. INSTALL PARKING BRAKE CABLE


  1. Install the parking brake cable with the 5 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C133096



    D028121E01
  1. Install the parking brake cable to the parking brake plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    D028481E01
  1. Install the spring cap into the body.

  1. Connect the cable end to the parking brake pull rod.



3. INSTALL PARKING BRAKE CABLE HEAT INSULATOR (for RH Side)


C133095
  1. Install the heat insulator with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



4. APPLY HIGH TEMPERATURE GREASE
  1. Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.



5. INSTALL PARKING BRAKE SHOE


F041705E03
  1. Apply high temperature grease to the adjusting bolt and piece.

  1. Using needle-nose pliers, connect the parking brake cable to the parking brake shoe lever.



    D028128
  1. Install the No. 1 shoe, hold down spring pin, hold down compression spring and 2 hold down spring cups.

  1. Install the return tension spring and shoe adjusting screw set.

  1. Install the No. 2 shoe, hold down spring pin, hold down compression spring and 2 hold down spring cups.



6. INSTALL PARKING BRAKE SHOE STRUT
  1. Attach the compression spring and parking brake shoe strut to the No. 2 and No. 1 shoes.



7. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING


D028127
  1. Using needle-nose pliers, install the 2 return tension springs.

    HINT:
    First install the front side spring then install the rear side spring.



8. CHECK PARKING BRAKE INSTALLATION


  1. Check that each part is installed properly.


    D028130E01

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining or the disc.



9. INSTALL REAR DISC
  1. Align the matchmarks of the disc and axle hub and install the disc.



10. ADJUST PARKING BRAKE SHOE CLEARANCE


D028131E01
  1. Provisionally install the 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the disc locks.

  1. Contract the shoe adjuster until the disc rotates smoothly.

    Standard:
    Return 8 notches

  1. Install the hole plug.



11. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


C133098
  1. Install the disc brake caliper with the 2 bolts and 2 washers.

    Torque:
    105 N*m{ 1,071 kgf*cm , 78 ft.*lbf }



12. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,137 kgf*cm , 82 ft.*lbf }



13. INSPECT PARKING BRAKE LEVER TRAVEL
  1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

    Parking brake lever travel:
    5 to 7 clicks at 200 N (20 kgf, 45 lbf)



14. ADJUST PARKING BRAKE LEVER TRAVEL


G022563
  1. Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    5 to 7 clicks at 200 N (20 kgf, 45 lbf)

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.



15. INSTALL FRONT CONSOLE BOX


    B133851
  1. Engage the 5 claws and install the front console box.

  1. Install the 4 <D> screws.



16. INSTALL BOX BOTTOM MAT


    B133899
  1. Install the box bottom mat.



17. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B133897
  1. Engage the 3 claws and 5 clips and install the console upper rear panel.



18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for 4WD)


    B133896
  1. Install the shift lever knob.



19. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transmission)


    B133894
  1. Install the shift lever knob.



20. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY


B133901E01
  1. Slide the parking brake hole cover toward the rear of the vehicle and engage the 2 C claws.

  1. Engage the 4 claws and install the parking brake hole cover.