REAR AXLE SHAFT > INSTALLATION |
| 1. INSTALL REAR AXLE SHAFT OIL SEAL |
![]() |
Using SST and a hammer, install a new oil seal.
Coat the lip of the oil seal with MP grease.
| 2. INSTALL REAR AXLE SHAFT |
Coat a new O-ring with MP grease and install it.
![]() |
Install the rear axle shaft together with the parking brake plate with the 4 nuts.
| 3. INSPECT REAR AXLE SHAFT BEARING |
![]() |
Inspect the axle shaft backlash.
Using a dial indicator, check the backlash near the center of the axle shaft.
![]() |
Inspect the axle shaft runout.
Using a dial indicator, check the runout of the surface of the axle shaft.
| 4. INSTALL REAR SPEED SENSOR |
![]() |
Install the rear speed sensor with the nut.
Connect the skid control sensor wire.
| 5. INSTALL PARKING BRAKE CABLE |
![]() |
Install the parking brake cable onto the parking brake plate with the 2 bolts.
| 6. APPLY HIGH TEMPERATURE GREASE |
Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.
| 7. INSTALL PARKING BRAKE SHOE |
![]() |
Apply high temperature grease to the adjusting bolt and piece.
Using needle-nose pliers, connect the parking brake cable to the parking brake shoe lever.
![]() |
Install the No. 1 shoe, hold down spring pin, hold down compression spring and 2 hold down spring cups.
Install the return tension spring and shoe adjusting screw set.
Install the No. 2 shoe, hold down spring pin, hold down compression spring and 2 hold down spring cups.
| 8. INSTALL PARKING BRAKE SHOE STRUT |
Attach the compression spring and parking brake shoe strut to the No. 2 and No. 1 shoes.
| 9. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING |
![]() |
Using needle-nose pliers, install the 2 return tension springs.
| 10. CHECK PARKING BRAKE INSTALLATION |
Check that each part is installed properly.

| 11. INSTALL REAR DISC |
Align the matchmarks of the disc and axle hub and install the disc.
| 12. ADJUST PARKING BRAKE SHOE CLEARANCE |
![]() |
Provisionally install the 2 hub nuts.
Remove the hole plug, and turn the adjuster to expand the shoe until the disc locks.
Contract the shoe adjuster until the disc rotates smoothly.
Install the hole plug.
| 13. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY |
![]() |
Install the disc brake caliper assembly with the 2 bolts and 2 washers.
Install the flexible hose with a new clip.
![]() |
Using SST, install the brake tube onto the flexible hose.
| 14. INSTALL REAR WHEEL |
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. INSPECT DIFFERENTIAL OIL |
![]() |
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the differential filler plug hole.
| Item | Capacity | |
| Front Differential | w/o A.D.D. | 1.35 to 1.45 Liters (1.43 to 1.53 US qts, 1.19 to 1.28 Imp qts.) |
| w/ A.D.D. | 1.50 to 1.60 Liters (1.59 to 1.69 US qts, 1.32 to 1.41 Imp qts.) | |
| Rear Differential | w/o Differential Lock | 2.45 to 2.55 Liters (2.59 to 2.69 US qts, 2.16 to 2.24 Imp qts.) |
| w/ Differential Lock | 2.40 to 2.50 Liters (2.54 to 2.64 US qts, 2.11 to 2.20 Imp qts.) | |
Check for oil leakage when the oil level is low.
Install the differential filler plug with a new gasket.
| 17. CHECK FOR DIFFERENTIAL OIL LEAKAGE |
| 18. BLEED BRAKE LINE |
Turn the ignition switch on (IG).
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid until the fluid level is between the MIN and MAX lines of the reservoir.
Repeatedly depress the brake pedal and bleed air from the bleeder plug of the front disc brake cylinder RH.
Repeat the step above until the air is completely bled, and then tighten the bleeder plug while depressing the brake pedal.
Bleed the air from the bleeder plug of the front disc brake cylinder LH using the same procedure as for the RH side.
With the brake pedal depressed, loosen the bleeder plug of the rear disc brake cylinder RH, continue to hold the brake pedal and allow brake fluid to be drained from the bleeder plug while the pump motor operates.
When there is no more air in the brake fluid, tighten the bleeder plug, and then release the brake pedal.
Bleed the air from the bleeder plug of the rear disc brake cylinder LH using the same procedure as for the RH side.
Turn the ignition switch off (IG).
Inspect for brake fluid leaks.
Check and adjust the brake fluid level .
| 19. INSPECT PARKING BRAKE LEVER TRAVEL |
Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.
| 20. ADJUST PARKING BRAKE LEVER TRAVEL |
![]() |
Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.
Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.
Check whether the parking brake drags or not.
When operating the parking brake lever, check that the brake warning light illuminates.
| 21. CHECK VSC SENSOR SIGNAL |