Home › ENGINE › 1GR-FE FUEL › FUEL SYSTEM

FUEL SYSTEM > PRECAUTION

for Preparation Click here



1.PRECAUTION
  1. Before working on the fuel system, disconnect the cable from the negative battery terminal.

  2. Do not work on the fuel system near any open flames. Never smoke when working on this system.

  3. Keep rubber and leather parts away from gasoline.


2.DISCHARGE FUEL SYSTEM PRESSURE (w/ Secondary Air Injection System)

CAUTION:
  1. Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.
  2. Even after discharging the fuel pressure, when disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



    A282108
  1. Disconnect the fuel pump control ECU assembly connector.

    1. Press the claw and move the lever in the direction of the arrow in the illustration.

    2. Disconnect the fuel pump control ECU assembly connector.

  2. Start the engine.

  3. After the engine stops naturally, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean (Bank 1)) or DTC P0174 (system too learn (Bank 2)) may be set.

  4. Crank the engine again and make sure that the engine does not start.

  5. Remove the fuel tank cap and discharge the pressure from the fuel tank.



  6. A282110
  7. Connect the fuel pump control ECU assembly connector.

    1. Connect the fuel pump control ECU assembly connector.

    2. Rotate the lever in the direction of the arrow until a "click" sound is heard.


3.DISCHARGE FUEL SYSTEM PRESSURE (w/o Secondary Air Injection System)

CAUTION:
  1. Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.
  2. Even after discharging the fuel pressure, when disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.

  1. Remove the circuit opening relay from the engine room relay block.

  2. Start the engine.

  3. After the engine stops naturally, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean (Bank 1)) or DTC P0174 (system too learn (Bank 2)) may be set.

  4. Crank the engine again and make sure that the engine does not start.

  5. Remove the fuel tank cap and discharge the pressure from the fuel tank.

  6. Install the circuit opening relay.


4.INJECTOR


    A223032E02
  1. Observe the following precautions when removing and installing the fuel injector.
    Text in Illustration 
    *a
    OK
    *b
    NG

    1. Do not reuse the O-ring and insulator.

    2. When placing a new O-ring onto the injector, do not damage the O-ring.

    3. Coat the new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.



  2. A223033E02
  3. Install the injector into the delivery pipe and lower intake manifold as shown in the illustration.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the injector, apply spindle oil or gasoline on the place where the delivery pipe contacts the O-ring of the injector.


5.FUEL SYSTEM


  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out, so observe these procedures.

    1. Discharge the fuel system pressure.

    2. Disconnect the fuel tank main tube .

    3. Drain the fuel remaining inside the fuel tank main tube.



    4. B000679E16
    5. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *1
      Plastic Bag

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.

    6. Put a container under the connection.



  2. Observe the following precautions when disconnecting the fuel tube connector (Quick Type A).



      A223364E02
    1. Fuel tube connector cover type:
      Disengage the lock claw by lifting up the cover, as shown in the illustration.
      Text in Illustration 
      *1
      Fuel Tube Connector Cover
      V100135
      Up



    2. A224870E02
    3. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
      Text in Illustration 
      *1
      Retainer
      *2
      Nylon Tube
      *3
      Pipe
      *4
      O-Ring
      *5
      Fuel Tube Connector



    4. A088336E27
    5. Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.
      Text in Illustration 
      *1
      Retainer
      V100135
      Pinch
      V100136
      Pull Out

      NOTICE:
      Do not use any tools.



    6. A193370
    7. If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.
      Text in Illustration 
      V100135
      Pull
      V100136
      Push

      NOTICE:
      Do not use any tools.

    8. Check the sealing surfaces of the disconnected parts, and clean them if necessary.



    9. A158902E02
    10. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *1
      Plastic Bag

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  3. A088339
  4. Observe the following precautions when connecting the fuel tube connectors (Quick Type A).
    Text in Illustration 
    V100136
    Push

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Line up the pipe and connector and push them together until a "click" sound is heard.

      HINT:
      If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



    3. A088340
    4. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
      Text in Illustration 
      V100136
      Pull

    5. Fuel tube connector cover type:
      Engage the lock claws to the connector by pushing down on the cover.

    6. Inspect for fuel leaks.



  5. A062772E03
  6. Observe the following procedure when disconnecting the fuel tube connectors (Quick Type B).
    Text in Illustration 
    *1
    Nylon Tube
    *2
    O-Ring
    *3
    Retainer
    *4
    Pipe

    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.



    2. A223368
    3. Disconnect them by hand.
      Text in Illustration 
      V100135
      Turn
      V100136
      Pull

      NOTICE:
      Do not use any tools.

    4. If the fuel tube connector and the pipe are stuck, push and pull on the fuel tube connector to release them. Pull the fuel tube connector out of the pipe carefully

      NOTICE:
      Do not use any tools.

    5. Check the sealing surfaces of the disconnected parts, and clean them if necessary.

    6. Protect the contact surface by covering it with a plastic bag.

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  7. A223369
  8. Observe the following procedure when connecting the fuel tube connector (Quick Type B).
    Text in Illustration 
    V100135
    Push

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Line up the pipe and connector and push them together until a "click" sound is heard.

      HINT:
      If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



    3. A223370
    4. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
      Text in Illustration 
      V100135
      Pull

    5. Inspect for fuel leaks.



  9. A224889E02
  10. Observe the following procedure when disconnecting the fuel tube connectors (Quick Type C).
    Text in Illustration 
    *1
    Pipe
    *2
    Retainer
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.



    2. A224877
    3. Pinch the tab on the retainer of the fuel tube connector to disengage the lock claws. Push it down as shown in the illustration.
      Text in Illustration 
      *1
      Retainer
      V100135
      Push
      V100136
      Down
      V100137
      Pull

      NOTICE:
      Do not use any tools.



    4. A091246E02
    5. If the fuel tube connector and the pipe are stuck, push and pull on the fuel tube connector to release them. Pull the fuel tube connector out of the pipe carefully.
      Text in Illustration 
      V100135
      Pull
      V100136
      Push

      NOTICE:
      Do not use any tools.

    6. Check the sealing surfaces of the disconnected parts, and clean them if necessary.



    7. A093309E05
    8. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *1
      Plastic Bag

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  11. A125397E03
  12. Observe the following procedure when connecting the fuel tube connector (Quick Type C).
    Text in Illustration 
    *1
    Retainer
    V100135
    Up
    V100136
    Push

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Line up the pipe and connector and push them together until a "click" sound is heard.

      HINT:
      If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



    3. A093435
    4. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
      Text in Illustration 
      V100136
      Pull



  13. A224872E02
  14. Observe these precautions when disconnecting the fuel tank breather tube connector:
    Text in Illustration 
    *1
    Fuel Tank Breather Tube Connector
    *2
    Pipe
    *3
    Nylon Tube
    *4
    O-Ring

    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.



    2. A224871E02
    3. Pinch the retainer and pull out the fuel tank breather tube connector with the fuel tank breather tube connector pushed to the pipe side to disconnect the fuel tank breather tube from the pipe.
      Text in Illustration 
      *1
      Fuel Tank Breather Tube Connector
      *2
      Pipe
      V100135
      Push
      V100136
      Pinch

      NOTICE:
      Do not use any tools.

    4. If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.

      NOTICE:
      Do not use any tools.

    5. Check the sealing surfaces of the disconnected parts, and clean them if necessary.

    6. Protect the contact surface by covering it with a plastic bag.

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  15. A224875
  16. Observe these precautions when connecting the fuel tank breather tube connector:
    Text in Illustration 
    V100135
    Push

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Align the fuel tank breather tube connector with the pipe, then push in the fuel tank breather tube connector until the retainer makes a "click" sound to install the fuel tank breather tube to the pipe.



    3. A224876
    4. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
      Text in Illustration 
      V100135
      Pull

    5. Inspect for fuel leak.


6.INSPECT FOR FUEL LEAK
  1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system .