Home › ENGINE › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSPECTION

for Preparation Click here



1. INSPECT CYLINDER HEAD SET BOLT


A224657E01
  1. Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
    Text in Illustration 
    *a
    Measurement Length

    Standard length:
    141.3 to 142.7 mm (5.56 to 5.62 in.)

    Maximum length:
    143.7 mm (5.66 in.)

    If the length is more than the maximum, replace the cylinder head set bolt.



    A226002
  1. Using a vernier caliper, measure the diameter of the elongated thread at the narrowest visible area.

    Standard diameter:
    10.73 to 10.97 mm (0.422 to 0.432 in.)

    Minimum diameter:
    10.40 mm (0.409 in.)

    If the diameter is less than the minimum, replace the cylinder head set bolt.

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.



2. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Turn the roller by hand to check that it turns smoothly.

    HINT:
    If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



3. INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the valve lash adjuster assembly free of dirt and foreign objects.
  2. Only use clean engine oil.

  1. Place the valve lash adjuster assembly into a container filled with engine oil.



    A109630E14
  1. Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
    Text in Illustration 
    *1
    Tapered Path
    *2
    Plunger
    *3
    Low Pressure Chamber
    *4
    Check Ball
    *5
    High Pressure Chamber
    *a
    CORRECT
    *b
    INCORRECT

    SST
    09276-75010  

  1. Squeeze SST and valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the valve lash adjuster assembly.



4. INSPECT CAMSHAFT
  1. Inspect the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum runout:
      0.04 mm (0.00157 in.)

      If the runout is greater than the maximum, replace the camshaft.

      HINT:
      Check the oil clearance after replacing the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard Cam Lobe Height:
    Item
    Specification
    Intake camshaft
    43.890 to 43.990 mm (1.728 to 1.732 in.)
    Exhaust camshaft
    44.262 to 44.362 mm (1.743 to 1.747 in.)

    Minimum Cam Lobe Height:
    Item
    Specification
    Intake camshaft
    43.84 mm (1.726 in.)
    Exhaust camshaft
    44.212 mm (1.741 in.)

  1. Using a micrometer, measure the journal diameter.

    Standard Journal Diameter:
    Item
    Specification
    No. 1 journal
    35.946 to 35.960 mm (1.4152 to 1.4157 in.)
    Other journals
    25.959 to 25.975 mm (1.0221 to 1.0226 in.)

    If the journal diameter is not as specified, check the oil clearance.



5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft place.

    NOTICE:
    Be careful not to damage the camshaft.



    A229667E01
  1. Put the camshaft timing gear assembly and camshaft together by aligning the key groove and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing gear assembly in the retard direction.

  1. Check that there is no clearance between the camshaft timing gear assembly flange and the camshaft.



    A229666
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the lock of the camshaft timing gear assembly.

    1. Fix the camshaft in place, and confirm that the camshaft timing gear assembly is locked.

      NOTICE:
      Be careful not to damage the camshaft.



    A106100E11
  1. Release the lock pin.
    Text in Illustration 
    *1
    Advance Side Path
    *2
    Retard Side Path
    *a
    Open
    *b
    Close
    V100144
    Rubber
    V100145
    Vinyl Tape

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A106101E08
    4. Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 opened paths.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A106102E09
    6. Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *a
      Hold Pressure
      *b
      Decompress

      HINT:
      This operation releases the lock pin at the most retarded position.

    7. When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from advance side path.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

      NOTICE:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear assembly locks at the most retarded position.



    A227959E02
  1. Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear assembly, be sure to release the straight pin lock before installing the camshaft timing gear assembly.



6. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227956E01
  1. Put the camshaft timing exhaust gear assembly and camshaft together by aligning the key groove and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing exhaust gear assembly in the retard direction.

  1. Check that there is no clearance between the gear flange and the camshaft.



    A229668
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the camshaft timing exhaust gear assembly lock.

    1. Make sure that the camshaft timing exhaust gear assembly locks.



    A106103E08
  1. Release the lock pin.
    Text in Illustration 
    *1
    Advance Side Path
    *2
    Retard Side Path
    *a
    Open
    *b
    Close
    V100144
    Rubber
    V100145
    Vinyl Tape

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A106104E04
    4. Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the 2 opened paths (the advance side path and the retard side path).
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A106105E06
    6. Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *a
      Hold Pressure
      *b
      Decompress

      HINT:
      The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.

    7. When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.

  1. Check for smooth rotation.

    1. Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.

      NOTICE:
      When the air pressure is released from the advance side path and then from the retard side path, the gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.

  1. Check the lock at the most advanced position.

    1. Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



    A227960E02
  1. Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



7. INSPECT CHAIN SUB-ASSEMBLY


A139523E06
  1. Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the chain sub-assembly by using a vernier caliper.
    Text in Illustration 
    *a
    Measuring Area

    Maximum chain elongation:
    136.9 mm (5.39 in.)

    HINT:
    Perform the measurement at 3 random places.

    If a measurement is more than the maximum, replace the chain sub-assembly.



8. INSPECT NO. 2 CHAIN SUB-ASSEMBLY
  1. Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 2 chain by using a vernier caliper.

    Maximum chain elongation:
    137.6 mm (5.42 in.)

    HINT:
    Perform the measurement at 3 random places.

    If a measurement is more than the maximum, replace the No. 2 chain sub-assembly.



9. INSPECT CRANKSHAFT TIMING SPROCKET


A131945
  1. Wrap the chain sub-assembly around the sprocket.

  1. Using a vernier caliper, measure the crankshaft timing sprocket diameter with the chain sub-assembly.

    Minimum gear diameter (with chain):
    61.0 mm (2.40 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.



10. INSPECT NO. 1 IDLE GEAR


A131946
  1. Wrap the chain sub-assembly around the gear.

  1. Using a vernier caliper, measure the No. 1 idle gear with the chain sub-assembly.

    Minimum gear diameter (with chain):
    61.0 mm (2.40 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain sub-assembly and No. 1 idle gear.



11. INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE
  1. Using a micrometer, measure the No. 1 idle gear shaft diameter.

    Standard idle gear shaft diameter:
    22.987 to 23.000 mm (0.905 to 0.906 in.)

  1. Using a caliper gauge, measure the inside diameter of the No. 1 idle gear.

    Standard idle gear inside diameter:
    23.02 to 23.03 mm (0.906 to 0.907 in.)

  1. Subtract the No. 1 idle gear shaft diameter measurement from the No. 1 idle gear inside diameter measurement.

    Standard oil clearance:
    0.020 to 0.043 mm (0.000787 to 0.00169 in.)

    Maximum oil clearance:
    0.093 mm (0.00366 in.)

    If the shaft oil clearance is more than the maximum, replace the No. 1 idle gear shaft and No. 1 idle gear.



12. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY


A120674E03
  1. Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *a
    Move
    If necessary, replace the No. 1 chain tensioner assembly.



13. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY


A131966E03
  1. Check that the plunger moves smoothly.
    Text in Illustration 
    *a
    Depth
    *b
    Move

  1. Measure the worn depth of the chain tensioner assembly.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.



14. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY


A131967E03
  1. Check that the plunger moves smoothly.
    Text in Illustration 
    *a
    Depth
    *b
    Move

  1. Measure the worn depth of the plunger.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.



15. INSPECT CHAIN TENSIONER SLIPPER


A222118E01
  1. Measure the worn depth of the chain tensioner slipper.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the chain tensioner slipper.



16. INSPECT NO. 1 CHAIN VIBRATION DAMPER


A222119E01
  1. Measure the depth of wear of the No. 1 chain vibration damper.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 1 chain vibration damper.



17. INSPECT NO. 2 CHAIN VIBRATION DAMPER


A222120E01
  1. Measure the depth of wear of the No. 2 chain vibration damper.
    Text in Illustration 
    *a
    Depth

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 2 chain vibration damper.



18. INSPECT CAMSHAFT THRUST CLEARANCE


A223707
  1. Install the camshafts .

  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.08 to 0.13 mm (0.00315 to 0.00512 in.)

    Maximum thrust clearance:
    0.15 mm (0.00591 in.)

    If the thrust clearance is more than the maximum, replace the camshafts.
    If necessary, replace the camshaft bearing caps and cylinder head as a set.



19. INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the camshaft bearing caps, camshaft housing sub-assembly and camshaft journals.

  1. Place the camshafts on the camshaft housing sub-assembly.



    A120715E04
  1. Lay a strip of Plastigage across each camshaft journal.
    Text in Illustration 
    *1
    Plastigage

  1. Install the camshaft bearing caps .

    NOTICE:
    Do not turn the camshaft.

  1. Remove the camshaft bearing caps .



    A221389E01
  1. Measure the Plastigage at its widest point.
    Text in Illustration 
    *1
    Plastigage
    *2
    No. 1 Journal
    *3
    Other Journals

    Standard Oil Clearance:
    Item
    Oil Clearance
    No. 1 journal
    0.040 to 0.079 mm (0.00157 to 0.00311 in.)
    Other journals
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Oil Clearance
    No. 1 journal
    0.10 mm (0.00394 in.)
    Other journals
    0.09 mm (0.00354 in.)

    If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.



20. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY


A222170
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.

    Maximum warpage:
    0.70 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold sub-assembly.



21. INSPECT INTAKE MANIFOLD FOR FLATNESS


A222115E02
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head and intake air surge tank.
    Text in Illustration 
    *a
    Intake Air Surge Tank Side
    *b
    Cylinder Head Side

    Maximum Warpage:
    Item
    Specified Condition
    Intake air surge tank side
    0.80 mm (0.0315 in.)
    Cylinder head side
    0.20 mm (0.00787 in.)

    If the warpage is more than the maximum, replace the intake manifold.