Home › ENGINE › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


A224725
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly from the timing chain cover sub-assembly.



2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A224726
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor from the rear water by-pass joint.

  1. Remove the gasket from the rear water by-pass joint.



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


A273790
  1. Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.



4. REMOVE VVT SENSOR


    A224729E01
  1. Remove the 2 bolts and 2 VVT sensors from the cylinder head cover sub-assembly LH.
    Text in Illustration 
    *a
    Bank 2



    A224728E01
  1. Remove the 2 bolts and 2 VVT sensors from the cylinder head cover sub-assembly.
    Text in Illustration 
    *a
    Bank 1



5. REMOVE CRANKSHAFT POSITION SENSOR


A224727
  1. Remove the bolt and crankshaft position sensor from the cylinder block sub-assembly.



6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A224731E01
  1. Remove the 2 bolts and 2 camshaft timing oil control valve assemblies from the cylinder head cover sub-assembly LH.
    Text in Illustration 
    *a
    Bank 2



    A224730E01
  1. Remove the 2 bolts and 2 camshaft timing oil control valve assemblies from the cylinder head cover sub-assembly.
    Text in Illustration 
    *a
    Bank 1

  1. Remove the 4 O-rings from the 4 camshaft timing oil control valve assemblies.



7. REMOVE OIL FILLER CAP HOUSING


A221161
  1. Remove the oil filler cap sub-assembly from the oil filler cap housing.

  1. Remove the 2 nuts and oil filler cap housing from the cylinder head cover sub-assembly LH.

  1. Remove the gasket from the oil filler cap housing.



8. REMOVE NO. 1 OIL PIPE


A223691
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe from the cylinder head cover sub-assembly LH and cylinder head LH.

  1. Remove the oil control valve filter LH and gaskets from the oil pipe union.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



9. REMOVE NO. 2 OIL PIPE


A223692
  1. Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe from the cylinder head cover sub-assembly and cylinder head sub-assembly.

  1. Remove the oil control valve filter RH and gaskets from the oil pipe union.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



10. REMOVE OIL FILTER ELEMENT


A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A222100
  1. Remove the oil filter drain plug.



    A222101E01
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A222102
  1. Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.



    A222103E01
  1. Using SST, remove the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A153538E03
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.



11. REMOVE OIL FILTER BRACKET


A225998
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket from the oil pan sub-assembly.



12. REMOVE WATER INLET HOUSING


A225380E01
  1. Disconnect the No. 1 water by-pass hose, No. 2 water by-pass hose and the No. 3 water by-pass hose from the water inlet housing.
    Text in Illustration 
    *1
    No. 1 Water By-pass Hose
    *2
    No. 2 Water By-pass Hose
    *3
    No. 3 Water By-pass Hose



    A223012
  1. Remove the 5 bolts and water inlet housing from the timing chain cover sub-assembly.



    A224736
  1. Remove the O-ring from the No. 1 water outlet pipe.

  1. Remove the gasket from the water pump assembly.



13. REMOVE REAR WATER BY-PASS JOINT


A076534E01
  1. Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets from the cylinder head sub-assembly and cylinder head LH.

  1. Remove the O-ring from the No. 1 water outlet pipe.



14. REMOVE SPARK PLUG


    A226864
  1. Remove the 6 spark plugs from the cylinder head sub-assembly.



15. REMOVE VENTILATION HOSE


A306499
  1. Loosen the hose clip and remove the ventilation hose from the ventilation valve sub-assembly.



16. REMOVE VENTILATION VALVE SUB-ASSEMBLY


    A306615
  1. Remove the ventilation valve sub-assembly from the cylinder head cover sub-assembly LH.



17. REMOVE CRANKSHAFT PULLEY


A072947E04
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E02
  1. Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt from the crankshaft.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A226542E01
  1. Remove the 12 bolts, seal washer and cylinder head cover sub-assembly LH from the camshaft housing sub-assembly LH and timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Seal Washer

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. Remove the No. 2 cylinder head cover gasket from the cylinder head cover sub-assembly LH.



    A223665
  1. Remove the 3 gaskets from the camshaft bearing caps.



19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A226543E01
  1. Remove the 12 bolts, seal washer and cylinder head cover sub-assembly from the camshaft housing sub-assembly RH and timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Seal Washer

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.



    A221164
  1. Remove the 3 gaskets from the camshaft bearing caps.



20. REMOVE SPARK PLUG TUBE GASKET


A124195E04
  1. Bend the ventilation baffle plate claws on the cylinder head cover sub-assembly to an angle of 90° or more.
    Text in Illustration 
    *a
    Bend

  1. Remove the 6 spark plug tube gaskets from the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

    NOTICE:
    Be careful not to damage the spark plug tube gasket when removing it, as the removed spark plug tube gasket needs to be used when installing a new one.



21. REMOVE OIL PAN DRAIN PLUG
  1. Remove the oil pan drain plug and gasket from the No. 2 oil pan sub-assembly.



22. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


A174340
  1. Remove the 10 bolts and 2 nuts from the No. 2 oil pan sub-assembly.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A174341E02
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



23. REMOVE OIL STRAINER SUB-ASSEMBLY


A245619
  1. Remove the 2 nuts, oil strainer sub-assembly and gasket from the oil pan sub-assembly.



24. REMOVE OIL PAN SUB-ASSEMBLY


A222173
  1. Remove the 17 bolts and 2 nuts from the oil pan sub-assembly.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A221168E02
  1. Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    LH Side:
    *b
    RH Side:
    *c
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block sub-assembly or oil pan sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    A222122
  1. Remove the 3 O-rings from the timing chain cover sub-assembly.



25. REMOVE NO. 1 OIL PAN BAFFLE PLATE


A224779
  1. Remove the 6 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.



26. REMOVE ENGINE REAR OIL SEAL RETAINER


A306597E01
  1. Remove the 5 bolts and 2 nuts from the cylinder block sub-assembly.

  1. Using a screwdriver with its tip wrapped in protective tape, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Pry



27. REMOVE REAR CRANKSHAFT OIL SEAL


A076248E03
  1. Using a screwdriver and hammer, tap out the rear crankshaft oil seal from the engine rear oil seal retainer.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.



28. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


A221169
  1. Remove the 26 bolts and the 2 nuts from the timing chain cover sub-assembly.



    A221170
  1. Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block sub-assembly or cylinder head sub-assembly.



    A221404
  1. Remove the oil pump gasket from the cylinder block sub-assembly.



29. REMOVE TIMING CHAIN COVER PLATE


A224737
  1. Remove the 4 bolts, timing chain cover plate and gasket from the timing chain cover sub-assembly.



30. REMOVE ENGINE WATER PUMP ASSEMBLY


A312625
  1. Remove the 8 bolts, engine water pump assembly and gasket from the timing chain cover sub-assembly.



31. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the front crankshaft oil seal from the timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.



32. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the crankshaft pulley bolt to the crankshaft.



    A222172E02
  1. Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH cylinder block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Crank Angle Sensor Plate
    *a
    RH Cylinder Block Bore Center Line
    *b
    Timing Mark



    A225378E03
  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *a
    Timing Mark



33. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


A306605E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *a
    Push
    *b
    Pin of 12.7 mm (0.05 in.) diameter

  1. Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.05 in.) diameter into the stopper plate hole.



    A095165E02
  1. Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.



34. REMOVE CHAIN TENSIONER SLIPPER


A223730
  1. Remove the chain tensioner slipper from the cylinder block sub-assembly.



35. REMOVE CHAIN SUB-ASSEMBLY


A221173E03
  1. Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Crank Angle Sensor Plate
    *a
    RH Cylinder Block Bore Center Line
    *b
    Timing Mark

  1. Remove the crankshaft pulley bolt from the crankshaft.



    A306606
  1. Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft timing sprocket.



    A095682E13
  1. Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.

  1. Remove the chain sub-assembly.
    Text in Illustration 
    *a
    Bank 1
    V100135
    Clockwise Approximately 60°



36. REMOVE NO. 1 IDLE GEAR SHAFT


A306610
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft from the cylinder block sub-assembly.



37. REMOVE NO. 1 CHAIN VIBRATION DAMPER


A223642
  1. Remove the 2 bolts and No. 1 chain vibration damper from the cylinder head LH and cylinder block sub-assembly.



38. REMOVE NO. 2 CHAIN VIBRATION DAMPER


A221176
  1. Remove the 2 No. 2 chain vibration dampers from the cylinder head sub-assembly and cylinder head LH.



39. REMOVE CRANKSHAFT TIMING SPROCKET


A306598
  1. Remove the crankshaft timing sprocket from the crankshaft.



40. REMOVE CRANKSHAFT TIMING GEAR KEY
  1. Remove the crankshaft timing gear key from the crankshaft.



41. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)


A221132E03
  1. While raising the plunger, insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Raise



    A306599E01
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly RH with a new one.

  1. Remove the 2 bolts from the camshaft and No. 2 camshaft.

  1. Remove the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH together with the No. 2 chain sub-assembly from the camshaft and No. 2 camshaft.



42. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


A306611
  1. Remove the bolt and No. 2 chain tensioner assembly from the camshaft housing sub-assembly RH.



43. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


A129700E06
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A221179E01
  1. Uniformly loosen and remove the 8 bolts in several steps and in the sequence shown in the illustration.



    A221180E01
  1. Uniformly loosen and remove the 12 bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft and No. 2 camshaft level.

  1. Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly RH.

  1. Remove the camshaft and No. 2 camshaft from the camshaft housing sub-assembly RH.



44. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


A312626E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly and camshaft housing sub-assembly RH.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly RH.



45. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)


A221182E04
  1. While pushing the plunger, insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Push



    A306600E01
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly LH with a new one.

  1. Remove the 2 bolts from the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly

  1. Remove the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH together with the No. 2 chain sub-assembly from the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly.



46. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


A306612
  1. Remove the bolt and No. 3 chain tensioner assembly from the camshaft housing sub-assembly LH.



47. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


A223636E01
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A221184E01
  1. Uniformly loosen and remove the 8 bolts in several steps and in the sequence shown in the illustration.



    A221185E01
  1. Uniformly loosen and remove the 13 bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly level.

  1. Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly LH.

  1. Remove the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly from the camshaft housing sub-assembly LH.



48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


A312627E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly LH by prying between the cylinder head LH and camshaft housing sub-assembly LH.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head LH and camshaft housing sub-assembly LH.



49. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly and cylinder head LH.

    HINT:
    Arrange the removed parts in the correct order.



50. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly and cylinder head LH.

    HINT:
    Arrange the removed parts in the correct order.



51. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head sub-assembly and cylinder head LH.

    HINT:
    Arrange the removed parts in the correct order.



52. REMOVE CYLINDER HEAD SUB-ASSEMBLY


A221092E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.



53. REMOVE CYLINDER HEAD GASKET


54. REMOVE CYLINDER HEAD LH


A221093E01
  1. Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.



    A221094E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.



55. REMOVE NO. 2 CYLINDER HEAD GASKET


56. REMOVE NO. 1 WATER OUTLET PIPE


    A178539
  1. Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts, bolt and No. 1 water outlet pipe.



57. REMOVE KNOCK SENSOR


    A075662
  1. Disconnect the 2 sensor connectors.

  1. Remove the 2 bolts and 2 sensors.



58. REMOVE CYLINDER BLOCK WATER JACKET SPACER


A225372
  1. Remove the 2 cylinder block water jacket spacers from the cylinder block sub-assembly.

    NOTICE:
    Be sure to remove the cylinder block water jacket spacers. If not, they may fall and become damaged when the cylinder block sub-assembly is inverted.



59. REMOVE TAPER SCREW PLUG

HINT:
It is not necessary to remove the taper screw plug unless it is being replaced.

  1. Remove the taper screw plug from the cylinder block sub-assembly.



60. REMOVE STRAIGHT PIN

HINT:
It is not necessary to remove the straight pin unless it is being replaced.

  1. Remove the 6 straight pins from the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.



61. REMOVE RING PIN

HINT:
It is not necessary to remove the ring pin unless it is being replaced.

  1. Remove the 20 ring pins from the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.



62. REMOVE STUD BOLT

HINT:
It is not necessary to remove the stud bolt unless it is being replaced.

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the cylinder head cover sub-assembly LH.

  1. Using an E6 and E8 "TORX" socket wrench, remove the 6 stud bolts from the oil pan sub-assembly.