CYLINDER BLOCK > DISASSEMBLY |
| 1. INSPECT CONNECTING ROD THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.
| 2. INSPECT CONNECTING ROD OIL CLEARANCE |
![]() |
Check the matchmarks on the connecting rod and cap to ensure correct reassembly.
Remove the 2 connecting rod cap bolts.
![]() |
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Clean the crank pin and bearing.
Check the crank pin and bearing for pitting and scratches. If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.
![]() |
Lay a strip of Plastigage across the crank pin.
| *1 | Plastigage |
Install the connecting rod cap .
Remove the 2 bolts, connecting rod cap and lower bearing.
![]() |
Measure the Plastigage at its widest point.
| *1 | Plastigage |
![]() |
| *a | Number Mark |
| Item | Specified Condition |
| Mark 1 | 59.000 to 59.006 mm (2.32283 to 2.32307 in.) |
| Mark 2 | 59.007 to 59.012 mm (2.32311 to 2.32330 in.) |
| Mark 3 | 59.013 to 59.018 mm (2.32334 to 2.32354 in.) |
| Mark 4 | 59.019 to 59.024 mm (2.32358 to 2.32377 in.) |
| Item | Specified Condition |
| Mark 1 | 1.484 to 1.487 mm (0.05843 to 0.05854 in.) |
| Mark 2 | 1.487 to 1.490 mm (0.05854 to 0.05866 in.) |
| Mark 3 | 1.490 to 1.493 mm (0.05866 to 0.05878 in.) |
| Mark 4 | 1.493 to 1.496 mm (0.05878 to 0.05900 in.) |
Completely remove the plastigage.
| 3. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
Push out the piston with connecting rod and upper bearing through the top of the cylinder block.
| 4. REMOVE CONNECTING ROD BEARING |
Remove the connecting rod bearings from the connecting rods and connecting rod caps.
| 5. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 compression rings.
Remove the 2 side rails and oil ring (expander) by hand.
| 6. REMOVE PISTON WITH PIN SUB-ASSEMBLY |
Disconnect the connecting rod from the piston.
![]() |
Using a screwdriver, pry out the 2 snap rings.
![]() |
Gradually heat the piston to approximately 80°C (176°F).
![]() |
Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.
| 7. INSPECT CRANKSHAFT THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.
| 8. INSPECT CRANKSHAFT OIL CLEARANCE |
![]() |
Uniformly loosen and remove the 8 bearing cap bolts and 8 seal washers in several steps, in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 16 bearing cap bolts in several steps, in the sequence shown in the illustration.
![]() |
Using a screwdriver, pry out the bearing caps. Remove the 4 bearing caps and lower bearings.
Remove the 2 lower crankshaft thrust washers.
Lift out the crankshaft.
![]() |
Remove the 2 upper thrust washers.
Clean each crankshaft journal and bearing.
Check each crankshaft journal and bearing for pitting and scratches.
If the journal or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.
Place the crankshaft on the cylinder block.
![]() |
Lay a strip of plastigage across each journal.
| *1 | Plastigage |
Install the crankshaft bearing cap .
Remove the crankshaft bearing cap.
![]() |
Measure the Plastigage at its widest point.
![]() |
If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for the appropriate bearing number. There are 5 sizes of standard bearings, marked "1", "2", "3", "4" and "5" accordingly.
| *a | Number Mark |
| Item | Specified Condition | ||||
| Cylinder block main journal bore diameter (A) + Crankshaft main journal diameter (B) | 0 to 5 | 6 to 11 | 12 to 17 | 18 to 23 | 24 to 28 |
| Use bearing | 1 | 2 | 3 | 4 | 5 |
| Mark | Specified Condition |
| Mark 00 | 77.000 mm (3.03149 in.) |
| Mark 01 | 77.001 mm (3.03152 in.) |
| Mark 02 | 77.002 mm (3.03156 in.) |
| Mark 03 | 77.003 mm (3.03160 in.) |
| Mark 04 | 77.004 mm (3.03164 in.) |
| Mark 05 | 77.005 mm (3.03168 in.) |
| Mark 06 | 77.006 mm (3.03172 in.) |
| Mark 07 | 77.007 mm (3.03176 in.) |
| Mark 08 | 77.008 mm (3.03180 in.) |
| Mark 09 | 77.009 mm (3.03184 in.) |
| Mark 10 | 77.010 mm (3.03188 in.) |
| Mark 11 | 77.011 mm (3.03192 in.) |
| Mark 12 | 77.012 mm (3.03196 in.) |
| Mark 13 | 77.013 mm (3.03200 in.) |
| Mark 14 | 77.014 mm (3.03204 in.) |
| Mark 15 | 77.015 mm (3.03208 in.) |
| Mark 16 | 77.016 mm (3.03211 in.) |
| Item | Specified Condition |
| Mark 00 | 71.999 to 72.000 mm (2.83460 to 2.83464 in.) |
| Mark 01 | 71.998 to 71.999 mm (2.83456 to 2.83460 in.) |
| Mark 02 | 71.997 to 71.998 mm (2.83452 to 2.83456 in.) |
| Mark 03 | 71.996 to 71.997 mm (2.83448 to 2.83452 in.) |
| Mark 04 | 71.995 to 71.996 mm (2.83440 to 2.83448 in.) |
| Mark 05 | 71.994 to 71.995 mm (2.83440 to 2.83444 in.) |
| Mark 06 | 71.993 to 71.994 mm (2.83436 to 2.83440 in.) |
| Mark 07 | 71.992 to 71.993 mm (2.83432 to 2.83436 in.) |
| Mark 08 | 71.991 to 71.992 mm (2.83428 to 2.83432 in.) |
| Mark 09 | 71.990 to 71.991 mm (2.83424 to 2.83428 in.) |
| Mark 10 | 71.989 to 71.990 mm (2.83420 to 2.83424 in.) |
| Mark 11 | 71.988 to 71.989 mm (2.83416 to 2.83420 in.) |
| Item | Specified Condition |
| Mark 1 | 2.488 to 2.491 mm (0.0980 to 0.0981 in.) |
| Mark 2 | 2.491 to 2.494 mm (0.0981 to 0.0982 in.) |
| Mark 3 | 2.494 to 2.497 mm (0.0982 to 0.0983 in.) |
| Mark 4 | 2.497 to 2.500 mm (0.0983 to 0.0984 in.) |
| Mark 5 | 2.500 to 2.503 mm (0.0984 to 0.0985 in.) |
Completely remove the plastigage.
| 9. REMOVE CRANKSHAFT |
Lift out the crankshaft.
Remove the 2 upper thrust washers.
| 10. REMOVE CRANKSHAFT BEARING |
Remove the crankshaft bearings from the bearing caps and cylinder block.
| 11. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon socket wrench, remove the 3 bolts and 3 oil nozzles.
| 12. REMOVE STUD BOLT |