Home › ENGINE › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL STUD BOLT


  1. Using an E6 and E8 "TORX" socket wrench, install the 6 stud bolts to the oil pan sub-assembly as shown in the illustration.


    A306601E03

    Torque:
    for stud bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for stud bolt B and C:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    A306602E01
  1. Using an E6 "TORX" socket wrench, install the 2 stud bolts to the cylinder head cover sub-assembly LH as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



2. INSTALL RING PIN


  1. Using a plastic-faced hammer, tap in 20 new ring pins to the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.


    A225382E02


    Text in Illustration 
    *a
    Camshaft Housing Sub-assembly LH
    *b
    Camshaft Housing Sub-assembly RH
    *c
    Protrusion Height
    -
    -

    Standard protrusion height:
    2.7 to 3.3 mm (0.106 to 0.130 in.)



3. INSTALL STRAIGHT PIN


  1. Using a plastic-faced hammer, tap in 6 new straight pins to the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.


    A225383E02


    Text in Illustration 
    *a
    Camshaft Housing Sub-assembly LH
    *b
    Camshaft Housing Sub-assembly RH
    *c
    Protrusion Height
    -
    -

    Standard Protrusion Height:
    Item
    Specified Condition
    Straight Pin A
    7.7 to 8.3 mm (0.303 to 0.327 in.)
    Straight Pin B
    5.7 to 6.3 mm (0.224 to 0.248 in.)



4. INSTALL TAPER SCREW PLUG
  1. Clean and degrease the threads of the taper screw plug and threads of the cylinder block sub-assembly.



    A301186E01
  1. Apply adhesive to 2 or 3 threads of the taper screw plug end.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.



    A270546
  1. Install the taper screw plug to the cylinder block sub-assembly.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Do not fill the engine coolant for at least 1 hour after installation.



5. INSTALL CYLINDER BLOCK WATER JACKET SPACER


A225710E03
  1. Install the 2 cylinder block water jacket spacers to the cylinder block sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    UP Mark
    *b
    L Mark
    *c
    R Mark

    NOTICE:
    Make sure that face the "L mark", "R mark" and "UP mark" are oriented as shown in the illustration.



6. INSTALL KNOCK SENSOR


    A078438E15
  1. Install the 2 sensors with the 2 bolts as shown in the illustration.
    Text in Illustration 
    *a
    for Bank 2:
    *b
    for Bank 1:
    *c
    Engine Rear
    *d
    Top
    *e
    Engine Front

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    Perform "Inspection After Repairs" after replacing the knock sensor (Click here).

  1. Connect the 2 sensor connectors.



7. INSTALL NO. 1 WATER OUTLET PIPE
  1. Install the No. 1 water outlet pipe with the 2 nuts and bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 wire harness clamps.



8. INSTALL CYLINDER HEAD GASKET
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.



    A222175E02
  1. Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.



    A221095E02
  1. Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front



9. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly (Click here).

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



  1. Step 1:



      A221092E02
    1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.

      NOTICE:
      Thoroughly wipe clean any seal packing.



10. INSTALL NO. 2 CYLINDER HEAD GASKET
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.



    A222176E02
  1. Apply seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    Gasket

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.5 to 3.0 mm (0.0984 to 0.118 in.)

    Seal packing application range 
    A
    10 to 15 mm (0.394 to 0.591 in.)
    B
    1.25 to 1.5 mm (0.0492 to 0.0591 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add engine oil within 2 hours of installation.



    A221096E02
  1. Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    Make sure that the gasket is installed facing the proper direction.

    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front



11. INSTALL CYLINDER HEAD LH
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Make sure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



  1. Step 1:



      A221094E02
    1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Step 2:

    1. Mark the front side of each cylinder head bolt head with paint.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3:

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the paint mark is now at a 180° angle to the front.



    A221093E02
  1. Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.



12. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the 24 valve stem caps.

  1. Install the 24 valve stem caps to the cylinder head sub-assembly and cylinder head LH.



13. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the 24 valve lash adjuster assemblies .

  1. Install the 24 valve lash adjuster assemblies to the cylinder head sub-assembly and cylinder head LH.

    NOTICE:
    Install the valve lash adjuster assemblies at the same place they were removed from.



14. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the valve lash adjuster assembly tips and valve stem cap ends.



    A221097E02
  1. Install the 24 No. 1 valve rocker arm sub-assemblies as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap



15. INSTALL CAMSHAFT BEARING CAP (for Bank 2)

HINT:
Perform "Inspection After Repairs" after replacing the No. 3 camshaft or No. 4 camshaft (Click here).

  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly LH and camshaft bearing caps.

  1. Install the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly to the camshaft housing sub-assembly LH.



    A224655
  1. Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.



    A221188E01
  1. Temporarily tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



16. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH


A221097E02
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No, 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap



    A221189E03
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A223640E01
  1. Install the camshaft housing sub-assembly LH to the cylinder head LH with the 13 bolts in the sequence shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.



    A221184E02
  1. Tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.



17. INSTALL CAMSHAFT BEARING CAP (for Bank 1)

HINT:
Perform "Inspection After Repairs" after replacing the camshaft or No. 2 camshaft (Click here).

  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly RH and camshaft bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly RH.



    A221190
  1. Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.



    A221387E01
  1. Temporarily tighten the 8 camshaft bearing cap bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH


A221097E02
  1. Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve
    *4
    Valve Stem Cap



    A221388E03
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A223641E01
  1. Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the sequence shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing sub-assembly RH, it is necessary to correctly position the camshafts as shown in the illustration.
      Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
    4. Do not start the engine for at least 2 hours after installing.



    A221179E02
  1. Tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Thoroughly wipe clean any seal packing.



19. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY


A222171E03
  1. Install the No. 3 chain tensioner assembly to the camshaft housing sub-assembly LH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the plunger and insert a pin a of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the tensioner.
    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Push



20. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

HINT:
Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly LH (Click here).



    A227957E03
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH as shown in the illustration.
    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.



    A306603E01
  1. Using SST to hold the hexagonal portion of each camshaft, install the 2 bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 3 chain tensioner assembly.



21. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY


A222174E03
  1. Install the No. 2 chain tensioner assembly to the camshaft housing sub-assembly RH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Push in the plunger and insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the tensioner.
    Text in Illustration 
    *1
    Plunger
    *a
    Pin of 1.0 mm (0.0394 in.) diameter
    *b
    Push



22. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

HINT:
Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly RH (Click here).



    A227958E02
  1. Align the mark plates (yellow) with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH as shown in the illustration.
    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft and No. 2 camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH with the No. 2 chain sub-assembly installed.



    A306604E01
  1. Using SST to hold the hexagonal portion of each camshaft, install the 2 bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner assembly.



23. INSTALL NO. 1 CHAIN VIBRATION DAMPER


A223642
  1. Install the No. 1 chain vibration damper to the cylinder block sub-assembly and cylinder head LH with the 2 bolts.

    Torque:
    23 N*m{ 229 kgf*cm , 17 ft.*lbf }



24. INSTALL NO. 2 CHAIN VIBRATION DAMPER


A221176
  1. Install the 2 No. 2 chain vibration dampers to the cylinder head sub-assembly and cylinder head LH.



25. INSTALL CRANKSHAFT TIMING GEAR KEY
  1. Using a plastic-faced hammer, tap in the crankshaft timing gear key to the crankshaft.



26. INSTALL CRANKSHAFT TIMING SPROCKET


A076293E02
  1. Install the crankshaft timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.
    Text in Illustration 
    *a
    Inward



27. INSTALL NO. 1 IDLE GEAR SHAFT
  1. Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.



    A312628E01
  1. Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block sub-assembly.
    Text in Illustration 
    *1
    No. 1 Idle Gear Shaft
    *2
    No. 1 Idle Gear
    *3
    No. 2 Idle Gear Shaft
    *4
    Knock Pin

    NOTICE:
    Make sure that the idle gear is installed facing the proper direction.

  1. Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }



28. INSTALL CHAIN SUB-ASSEMBLY


A223644E03
  1. Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly.
    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

    HINT:
    The camshaft timing gear assembly mark plates are orange.



    A306606
  1. Do not pass the chain over the crankshaft, just temporarily place it on the crankshaft timing sprocket.



    A223645E02
  1. Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.
    Text in Illustration 
    *1
    Chain Plate
    *a
    When the No. 1 idle gear is reused
    *b
    Mark
    *c
    Align
    *d
    Turn

    NOTICE:
    When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been in sequence to tighten the chain sub-assembly between the banks.



    A223646E02
  1. Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly to the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Mark Plate
    *a
    Timing Mark

    HINT:
    The crankshaft timing sprocket mark plate is yellow.

  1. Temporarily tighten the crankshaft pulley bolt.



    A223647E02
  1. Turn the crankshaft clockwise to set it to the RH cylinder block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Crank Angle Sensor Plate
    *a
    RH Cylinder Block Bore Center Line
    *b
    Timing Mark



29. INSTALL CHAIN TENSIONER SLIPPER


A223730
  1. Install the chain tensioner slipper to the cylinder block sub-assembly.



30. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


A178214E04
  1. Turn the stopper plate of the tensioner clockwise and push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.
    Text in Illustration 
    *1
    Stopper Plate
    *2
    Plunger
    *a
    Push

  1. Turn the stopper plate of the tensioner counterclockwise and insert a pin of 1.27 mm (0.05 in.) diameter into the holes on the stopper plate and tensioner to fix the stopper plate in place.



    A095165E02
  1. Install the No. 1 chain tensioner assembly to the cylinder head sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the No. 1 chain tensioner assembly.



31. INSPECT VALVE TIMING
  1. Check the camshaft timing marks.

    NOTICE:
    1. Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
    2. If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.



  1. Check that each camshaft timing mark is positioned as shown in the illustration.


    A223648E05


    Text in Illustration 
    *a
    Timing Mark
    *b
    Viewpoint

    HINT:
    A182780E01
    for the intake camshaft:
    Be sure to check mark A at the point when marks B, C, and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.

  1. If the valve timing is misaligned, reinstall the chain sub-assembly.

  1. Remove the crank pulley bolt.



32. INSTALL FRONT CRANKSHAFT OIL SEAL


A225390E01
  1. Using SST and a hammer, tap in a new front crankshaft oil seal until its surface is flush with the timing chain cover sub-assembly edge.

    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the front crankshaft oil seal at an angle.
    3. Make sure that the front crankshaft oil seal edge does not stick out of the timing chain cover sub-assembly.



33. INSTALL ENGINE WATER PUMP ASSEMBLY


A312625
  1. Install a new gasket and engine water pump assembly to the timing chain cover sub-assembly with the 8 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



34. INSTALL TIMING CHAIN COVER PLATE
  1. Install a new gasket and the timing chain cover plate to the timing chain cover sub-assembly with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



35. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover sub-assembly, cylinder head sub-assembly and cylinder block sub-assembly.


    A225681E02


    Text in Illustration 
    *a
    Cylinder head and cylinder block side:
    *b
    Timing chain cover side:
    *c
    Clean and degrease
    -
    -

    NOTICE:
    Be sure to clean and degrease the contact surfaces, especially the surfaces indicated in the illustration.

  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket to the cylinder block sub-assembly.



    A225682E01
  1. Apply seal packing as shown in the illustration.
    Text in Illustration 
    *1
    Seal Diameter
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)



  1. Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.


    A221403E01


    Text in Illustration 
    *a
    Be sure to apply seal packing
    *b
    Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *c
    Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *d
    Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)
    *e
    Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    -
    -

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. When there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.


    Application Specification:

    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm (0.177 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Alternate Long and Short Dashed Line Area
    3.5 mm (0.138 in.) or more
    2.0 to 3.0 mm (0.0787 to 0.118 in.)
    Dashed Line Area
    3.5 mm (0.138 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Diagonal Line Area
    6.0 mm (0.236 in.) or more
    5.0 mm (0.197 in.)



    A221405E01
  1. Align the oil pump drive rotor spline and the crankshaft as shown in the illustration. Install the spline and timing chain cover sub-assembly to the crankshaft.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft



  1. Install the timing chain cover sub-assembly with the 26 bolts labeled A, B, C, D and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.


    A221406E01


    Text in Illustration 
    *1
    Nut
    -
    -
    *a
    Area 1
    *b
    Area 2
    *c
    Area 3
    *d
    Area 4

    Bolt Length:
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    35 mm (1.38 in.)
    Bolt D
    65 mm (2.56 in.)

    NOTICE:
    Make sure that there is no oil on the bolt threads.

  1. Fully tighten the bolts in Area 1.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

  1. Fully tighten the bolts in Area 2.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  1. Fully tighten the bolts in Area 3.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts and nuts from top to bottom as shown in the illustration.

  1. Fully tighten the bolts in Area 4.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

    NOTICE:
    1. Do not start the engine for at least 2 hours after installing it.
    2. Wipe off any seal packing that seeped out around the surfaces of the oil pan and head cover and make sure that there is no seal packing seeping out around the edges.



36. INSTALL REAR CRANKSHAFT OIL SEAL


A306613E01
  1. Using SST and a hammer, tap in a new rear crankshaft oil seal until its surface is flush with the engine rear oil seal retainer edge.

    SST
    09223-78010  

  1. Apply MP grease to the lip of the rear crankshaft oil seal.



37. INSTALL ENGINE REAR OIL SEAL RETAINER
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the engine rear oil seal retainer or cylinder block sub-assembly.



    A076269E07
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the engine rear oil seal retainer within 3 minutes after applying seal packing.

  1. Install the engine rear oil seal retainer to the cylinder block sub-assembly with the 5 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. When installing the engine rear oil seal retainer, make sure the lip of the rear crankshaft oil seal is not damaged.
    2. When installing the engine rear oil seal retainer, make sure the lip of the rear crankshaft oil seal is not folded incorrectly.
    3. Do not start the engine for at least 2 hours after installation.



38. INSTALL NO. 1 OIL PAN BAFFLE PLATE


A224779
  1. Install the No. 1 oil pan baffle plate to the oil pan sub-assembly with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



39. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block sub-assembly, engine rear oil seal retainer and oil pan sub-assembly.

  1. Install 3 new O-rings to the timing chain cover sub-assembly.



    A222121E02
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan sub-assembly within 3 minutes after applying seal packing.



    A223671E01
  1. Install the oil pan sub-assembly with the 17 bolts (A, B, C, D and E) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
    Text in Illustration 
    *1
    Nut

    Torque:
    for bolt A, B, C, E and nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Bolt Length:
    Item
    Length
    Bolt A
    60 mm (2.36 in.)
    Bolt B
    45 mm (1.77 in.)
    Bolt C
    25 mm (0.984 in.)
    Bolt D
    16 mm (0.630 in.)
    Bolt E
    70 mm (2.76 in.)

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



40. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer to the oil pan sub-assembly with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



41. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


A174349E03
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan sub-assembly within 3 minutes after applying seal packing.



    A225446
  1. Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.
    2. Do not start the engine for at least 2 hours after the installation.



42. INSTALL OIL PAN DRAIN PLUG
  1. Install a new gasket and oil pan drain plug to the No. 2 oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



43. POUR ENGINE OIL


A224782

HINT:
Before installing the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH, pour engine oil into the locations shown in the illustration.



44. INSTALL SPARK PLUG TUBE GASKET


A100218E05
  1. Using a utility knife, cut off the seal part of the removed spark plug tube gasket.
    Text in Illustration 
    V100155
    Area to cut off



    A226558E02
  1. Using the removed spark plug tube gasket and a hammer, tap in a new spark plug tube gasket until it stops.
    Text in Illustration 
    *1
    Removed Spark Plug Tube Gasket
    *2
    New Spark Plug Tube Gasket

    HINT:
    If the removed spark plug tube gasket does not fit on the new one, correct the removed one with pliers.

  1. Apply a light coat of MP grease to the spark plug tube gasket lip.

  1. Return the ventilation baffle plate claws to the original positions.



45. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the camshaft housing sub-assembly RH, timing chain cover sub-assembly or cylinder head cover sub-assembly.



    A223667
  1. Apply seal packing as shown in the illustration.
    Text in Illustration 
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A221164
  1. Install 3 new gaskets to the camshaft bearing caps as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. Install a new seal washer to the bolt.



    A221162E02
  1. Temporarily install the cylinder head cover sub-assembly to the camshaft housing sub-assembly and timing chain cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.
    Text in Illustration 
    *1
    Seal Washer
    V100135
    Bolt A (25 mm (0.984 in.))
    V100136
    Bolt B (35 mm (1.38 in.))
    V100137
    Bolt C (65 mm (2.56 in.))
    V100138
    Bolt D (60 mm (2.36 in.))

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



46. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old seal packing material and be careful not to drop any oil on the contact surfaces of the camshaft housing sub-assembly LH, timing chain cover sub-assembly or cylinder head cover sub-assembly LH.



    A223664
  1. Apply seal packing as shown in the illustration.
    Text in Illustration 
    V100135
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A223665
  1. Install 3 new gaskets to the camshaft bearing caps as shown in the illustration.

  1. Install a new No. 2 cylinder head cover gasket to the cylinder head cover sub-assembly LH.

  1. Install a new seal washer to the bolt.



    A221163E02
  1. Temporarily install the cylinder head cover sub-assembly LH to the camshaft housing sub-assembly LH and timing chain cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.
    Text in Illustration 
    *1
    Seal Washer
    V100135
    Bolt A (25 mm (0.984 in.))
    V100136
    Bolt B (35 mm (1.38 in.))
    V100137
    Bolt C (70 mm (2.76 in.))
    V100138
    Bolt D (60 mm (2.36 in.))

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



47. INSTALL CRANKSHAFT PULLEY


A076309E03
  1. Using SST, install the crankshaft pulley to the crankshaft with the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }



48. INSTALL VENTILATION VALVE SUB-ASSEMBLY
  1. Clean and degrease the threads of the ventilation valve sub-assembly and threads of the cylinder head cover sub-assembly LH.



    A302814E01
  1. Apply adhesive to 2 or 3 threads of the ventilation valve sub-assembly.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.



    A306615
  1. Install the ventilation valve sub-assembly to the cylinder head cover sub-assembly LH.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



49. INSTALL VENTILATION HOSE


A306499
  1. Install the ventilation hose to the ventilation valve sub-assembly with the hose clip.



50. INSTALL SPARK PLUG
  1. Install the 6 spark plugs to the cylinder head sub-assembly.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



51. INSTALL REAR WATER BY-PASS JOINT


A306614E01
  1. Apply soapy water to a new O-ring and install it to the No. 1 water outlet pipe.
    Text in Illustration 
    *1
    O-ring
    *2
    Gasket

  1. Install 2 new gaskets to the cylinder head sub-assembly and cylinder head LH.



    A076534E01
  1. Install the rear water by-pass joint to the cylinder head sub-assembly and cylinder head LH with the 2 bolts and 4 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



52. INSTALL WATER INLET HOUSING
  1. Apply soapy water to a new O-ring, install it to the No. 1 water outlet pipe.

  1. Install a new gasket to the water pump assembly.

  1. Install the water inlet housing to the timing chain cover sub-assembly with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the No. 1 water by-pass hose, No. 2 water by-pass hose and No. 3 water by-pass hose to the water inlet housing.



53. INSTALL OIL FILTER BRACKET
  1. Install the oil filter bracket and new gasket to the oil pan sub-assembly with the 2 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



54. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, the threads and O-ring groove.



    A284599E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element to the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.



    A284600E01
  1. Using SST, tighten the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket
    *2
    O-Ring
    *3
    Oil Filter Cap
    *4
    Oil Filter Bracket Clip
    *a
    No Gap

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. Make sure that the oil filter is installed securely as shown in the illustration.
    3. Be careful that the O-ring does not get caught between the parts.
    4. After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



    A222105E01
  1. Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.



55. INSTALL NO. 2 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the No. 2 oil pipe (on the cylinder head side) with the oil pipe union.

  1. Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



56. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head side) with the oil pipe union.

  1. Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



57. INSTALL OIL FILLER CAP HOUSING


A221161E02
  1. Install a new gasket to the oil filler cap housing.
    Text in Illustration 
    *1
    Gasket

  1. Install the oil filler cap housing to the cylinder head cover sub-assembly LH with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the oil filler cap sub-assembly to the oil filler cap housing.



58. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Apply a light coat of engine oil to 4 new O-rings.

  1. Install the 4 O-rings to the 4 camshaft timing oil control valve assemblies.



    A224730E02
  1. Install the 2 camshaft timing oil control valve assemblies to the cylinder head cover sub-assembly with the 2 bolts.
    Text in Illustration 
    *a
    Bank 1

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve assembly.



    A224731E02
  1. Install the 2 camshaft timing oil control valve assemblies to the cylinder head cover sub-assembly LH with the 2 bolts.
    Text in Illustration 
    *a
    Bank 2

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring is not cracked when installing the camshaft timing oil control valve assembly.



59. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

    NOTICE:
    1. When reusing the crankshaft position sensor, inspect the O-ring.
    2. If the O-ring has scratches or cuts, replace the crankshaft position sensor.



    A224727
  1. Install the crankshaft position sensor to the cylinder block sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



60. INSTALL VVT SENSOR
  1. Apply a light coat of engine oil to the O-ring of the 4 VVT sensors.

    NOTICE:
    1. When reusing the VVT sensor, inspect the O-ring.
    2. If the O-ring has scratches or cuts, replace the VVT sensor.



    A224728E01
  1. Install the 2 VVT sensors to the cylinder head cover sub-assembly with the 2 bolts.
    Text in Illustration 
    *a
    Bank 1

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A224729E01
  1. Install the 2 VVT sensors to the cylinder head cover sub-assembly LH with the 2 bolts.
    Text in Illustration 
    *a
    Bank 2

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



61. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Clean and degrease the threads of the cylinder block water drain cock sub-assembly and threads of the cylinder block sub-assembly.



    A076531E20
  1. Apply adhesive to 2 or 3 threads of the cylinder block water drain cock sub-assembly end.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.



    A273791E03
  1. Install the cylinder block water drain cock sub-assembly to the cylinder block sub-assembly.
    Text in Illustration 
    *a
    Front

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Do not fill the engine coolant for at least 1 hour after installation.

  1. Rotate the cylinder block water drain cock sub-assembly clockwise as shown in the illustration.

    NOTICE:
    1. Do not rotate the cylinder block water drain cock sub-assembly by more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.
    2. Do not loosen the cylinder block water drain cock sub-assembly after setting it correctly.



62. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

HINT:
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor (Click here).

  1. Install a new gasket to the engine coolant temperature sensor.



    A224726
  1. Using a 19 mm deep socket wrench, install the engine coolant temperature sensor to the rear water by-pass joint.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



63. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Clean and degrease the threads of the engine oil pressure switch assembly and threads of the timing chain cover sub-assembly.



    A105862E01
  1. Apply adhesive to 2 or 3 threads of the engine oil pressure switch assembly.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    1. To prevent contamination by foreign matter, install immediately after applying adhesive.
    2. Do not apply adhesive to the oil inlet port of the engine oil pressure switch assembly.



    A224725
  1. Using a 24 mm deep socket wrench, install the engine oil pressure switch assembly to the timing chain cover sub-assembly.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }