Home › ENGINE › 1GR-FE ENGINE MECHANICAL › CYLINDER BLOCK

CYLINDER BLOCK > REASSEMBLY

for Preparation Click here



1. INSTALL STUD BOLT


  1. Install new stud bolts.

    Torque:
    for stud bolt A and C:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for stud bolt B and D:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    A221128E02


    Text in Illustration 
    *a
    Front Side:
    *b
    Upper Side:
    *c
    Lower Side:
    *d
    Rear Side:



2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY


A120734
  1. Using a 5 mm hexagon socket wrench, install the 3 oil nozzles with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



3. INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the piston with pin sub-assembly (Click here).



    A221130
  1. Using a screwdriver, install a new snap ring on one side of the piston pin hole.

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



    P012417E12
  1. Gradually heat the piston to approximately 80°C (176°F).



    A221131E02
  1. Coat the piston pin with engine oil.

  1. Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

    HINT:
    The piston and pin are a matched set.

    Text in Illustration 
    *a
    Front Mark

  1. Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.



    A223711
  1. Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

    HINT:
    Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



4. INSTALL PISTON RING SET

HINT:
Perform "Inspection After Repairs" after replacing the piston ring set (Click here).

  1. Install the oil ring (expander) and 2 side rails by hand.



    A221133E02
  1. Using a piston ring expander, install the 2 compression rings with the painted mark on the right side.
    Text in Illustration 
    *1
    No. 1 Compression Ring
    *2
    No. 2 Compression Ring
    *a
    Painted Mark
    V100135
    Right Side



    A221134E02
  1. Position the piston rings so that the ring ends are as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Compression Ring
    *2
    No. 2 Compression Ring
    *3
    Lower Side Rail
    *4
    Upper Side Rail
    *5
    Expander
    *a
    Front Mark



5. INSTALL CRANKSHAFT BEARING

HINT:
A223696E02
Main bearings come in widths of 17.3 mm (0.681 in.) and 19.9 mm (0.783 in.). Install the 19.9 mm (0.783 in.) bearings in the No. 1 and No. 4 cylinder block journal positions with the bearing caps. Install the 17.3 mm (0.681 in.) bearings in the No. 2 and No. 3 positions.
Text in Illustration 
*a
No. 1 and No. 4 Journal Bearings:
*b
No. 2 and No. 3 Journal Bearings:

  1. Clean each main journal and bearing.



  1. Install the upper bearing.



      A183116E02
    1. Install the upper bearing to the cylinder block as shown in the illustration.
      Text in Illustration 
      *a
      CORRECT
      *b
      INCORRECT

      NOTICE:
      1. Do not apply engine oil to the bearings or contact surfaces.
      2. Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.
      3. Do not allow coolant to come into contact with the inner surface of the bearing.
      4. If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.



    A183118E03
  1. Install the lower bearing.
    Text in Illustration 
    *1
    Vernier Caliper
    *a
    Mark 1, 2, 3 or 4

    1. Install the lower bearings to the crankshaft bearing caps.

    2. Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.

      Dimension A - B or B - A:
      0 to 0.7 mm (0 to 0.0276 in.)

      NOTICE:
      1. Do not apply engine oil to the bearings or contact surfaces.
      2. Do not allow coolant to come into contact with the inner surface of the bearing.
      3. If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.



6. INSTALL CRANKSHAFT

NOTICE:
Clean the contact surface of each main journal and crank pin.

  1. Apply new engine oil to the upper bearing and install the crankshaft to the cylinder block.



    A229670
  1. Push the crankshaft in the rear thrust direction to create clearance and install a thrust washer to the No. 2 journal position with the oil groove facing the front of the engine.

  1. Push the crankshaft in the forward thrust direction to create clearance and install a thrust washer to the No. 2 journal position with the oil groove facing the rear of the engine.



    A229671
  1. Install the 2 lower thrust washers to the No. 2 bearing cap with the grooves facing outward.



    A221135
  1. Examine the front marks and numbers and set the crankshaft bearing caps on the cylinder block.

  1. Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.

  1. Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.



    A221136E01
  1. Tighten the 2 bolts for each bearing cap until the clearance between the crankshaft bearing cap and the cylinder block becomes less than 6 mm (0.236 in.).
    Text in Illustration 
    *a
    Less than 6 mm



    A221137
  1. Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.



    A184806E01
  1. Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts and temporarily install the 8 crankshaft bearing bolts to the outside positions.



  1. Tighten the crankshaft bearing cap bolts.

    HINT:
    The cap bolts are tightened in 2 progressive steps.




      A221138E01
    1. Step 1:
      Uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

      Torque:
      61 N*m{ 622 kgf*cm , 45 ft.*lbf }

    2. Mark the front side of the crankshaft bearing cap bolts with paint.

    3. Step 2:
      Tighten the bearing cap bolts 90° in the order shown in step 1.

    4. Check that the painted marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.



    A221139E01
  1. Install and uniformly tighten the 8 main bearing cap bolts together with 8 new seal washers in several steps in the sequence shown in the illustration.
    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

    Torque:
    26 N*m{ 262 kgf*cm , 19 ft.*lbf }

    Bolt Length:
    Item
    Length
    Bolt A
    45 mm (1.77 in.)
    Bolt B
    30 mm (1.18 in.)

  1. Check that the crankshaft turns smoothly.



7. INSTALL CONNECTING ROD BEARING


    A177653E02
  1. Install the bearing to the connecting rod cap.
    Text in Illustration 
    *1
    Vernier Caliper
    *2
    Connecting Rod Cap
    *3
    Connecting Rod Bearing

    NOTICE:
    1. Clean the contact surfaces of the bearing and connecting rod cap.
    1. Do not apply engine oil to the bearing or the surface it contacts.

  1. Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

    Dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)



    A177654E02
  1. Install the bearing to the connecting rod.
    Text in Illustration 
    *1
    Vernier Caliper
    *2
    Connecting Rod
    *3
    Connecting Rod Bearing

    NOTICE:
    1. Clean the contact surface of the bearing and connecting rod.
    1. Do not apply engine oil to the bearing or the surface it contacts.

  1. Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

    Dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)



8. INSPECT CRANKSHAFT THRUST CLEARANCE


A221124
  1. Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.00157 to 0.00945 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    1.93 to 1.98 mm (0.0760 to 0.0780 in.)

    If necessary, replace the crankshaft.



9. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD
  1. Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.



    A221134E02
  1. Check the positions of the piston ring ends.
    Text in Illustration 
    *1
    No. 1 Compression Ring
    *2
    No. 2 Compression Ring
    *3
    Lower Side Rail
    *4
    Upper Side Rail
    *5
    Expander
    *a
    Front Mark



    A221140E02
  1. Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.
    Text in Illustration 
    *a
    Front Mark



    A221141E03
  1. Install each connecting rod cap so that the protrusion is facing the correct direction.
    Text in Illustration 
    *a
    Protrusion
    V100135
    Front

    NOTICE:
    Match each numbered connecting rod cap with the correct connecting rod.

  1. Apply a light coat of engine oil to the threads of the connecting rod cap bolts.



  1. Install the connecting rod cap bolts.

    HINT:
    The cap bolts are tightened in 2 progressive steps.




      A221142
    1. Step 1:
      Install and alternately tighten the bolts of each connecting rod cap in several steps.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    2. Mark the front side of each connecting rod cap bolt with paint.

    3. Step 2:
      Tighten the cap bolts 90°.

  1. Check that the painted mark is now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.



10. INSPECT CONNECTING ROD THRUST CLEARANCE


A221120
  1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.30 mm (0.00591 to 0.0118 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)

    If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.

    Standard connecting rod thickness:
    20.80 to 20.85 mm (0.819 to 0.821 in.)

    If necessary, replace the crankshaft.