OIL AND OIL FILTER > REPLACEMENT |
| 1. REMOVE ENGINE UNDER COVER SEAL |
![]() |
Remove the 2 bolts and engine under cover seal.
| 2. DISCONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and open the No. 1 engine under cover as shown in the illustration.
| 3. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
| 4. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
| *1 | Pipe |
| *2 | Hose |
![]() |
Remove the oil filter drain plug.
![]() |
Install the pipe to the oil filter cap.
| *1 | Cap |
| *2 | Valve |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Hose |
![]() |
Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.
![]() |
Using SST, remove the oil filter cap.
| *1 | Oil Filter Bracket Clip |
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | O-Ring |
| 5. INSTALL OIL FILTER ELEMENT |
Clean the inside of the oil filter cap, the threads and O-ring groove.
![]() |
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
| *1 | O-Ring |
| *a | CORRECT |
| *b | INCORRECT |
Set a new oil filter element to the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.
![]() |
Using SST, tighten the oil filter cap.
| *1 | Oil Filter Bracket |
| *2 | O-Ring |
| *3 | Oil Filter Cap |
| *4 | Oil Filter Bracket Clip |
| *a | No Gap |
![]() |
Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
| *1 | O-Ring |
Install the oil filter drain plug.
| 6. ADD ENGINE OIL |
Add fresh oil.
![]() |
| Oil grade | Oil Viscosity (SAE) |
| ILSAC GF-5 multigrade engine oil | 0W-20 |
| Oil grade | Oil Viscosity (SAE) |
| API grade SL "Energy- Conserving", SM "Energy- Conserving", SN "Resource-Conserving", or ILSAC multigrade engine oil | 0W-20 5W-20 5W-30 10W-30 |
| API grade SL, SM or SN multigrade engine oil | 15W-40 20W-50 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 5.7 liters (6.0 US qts, 5.0 Imp. qts) |
| Drain and refill with oil filter change | 6.1 liters (6.4 US qts, 5.4 Imp. qts) |
| Dry fill | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
Install the oil filler cap.
| 7. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 8. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 9. CONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
Install the 4 bolts to close the No. 1 engine under cover.
| 10. INSTALL ENGINE UNDER COVER SEAL |
Install the engine under cover seal with the 2 bolts.