Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the clutch start switch or the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM


A226248E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned ON and the engine starts.

    OK:
    Condition
    Starter Signal
    Ignition switch ON
    OFF
    Engine start
    ON

Result 
Result
Proceed to
NG (for manual transmission models)
A
NG (for automatic transmission models)
B
OK (for manual transmission models)
C
OK (for automatic transmission models)
D


B
Go to step 6

C
Go to step 5

D
Go to step 9
A


2.INSPECT CLUTCH START SWITCH ASSEMBLY
A159771E27
  1. Remove the clutch start switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    ON (pushed)
    Below 1 Ω
    1 - 2
    OFF (free)
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Clutch Start Switch Assembly)



NG
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
OK


3.INSPECT IGNITION SWITCH ASSEMBLY
A116847E05
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (AM1) - 1 (ST1)
    START position
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
  1. Disconnect the ignition switch connector.

  1. Disconnect the clutch start switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) - A9-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) or A9-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM - STA RELAY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (STA relay) - E77-10 (STA)
    Always
    Below 1 Ω
    1 (STA relay) - A9-2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E77-10 (STA) or A9-2 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    Outside standard range
    A
    Within standard range
    B



B
Go to step 10
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C193931E02
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 5
    Shift position P, N
    Below 1 Ω
    4 - 5
    Shift position not P, N
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Park/Neutral Position Switch Assembly)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


7.INSPECT IGNITION SWITCH ASSEMBLY
A116847E05
  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (AM1) - 1 (ST1)
    START position
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the ignition switch connector.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) - B35-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A1-1 (ST1) or B35-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - STA RELAY)
  1. Remove the STA relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (STA relay) - E77-10 (STA)
    Always
    Below 1 Ω
    1 (STA relay) - B35-5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E77-10 (STA) or B35-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


11.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

REPAIR OR REPLACE STARTER CIRCUIT (STARTER - STA RELAY)