Home › ENGINE › 1GR-FE ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts from the No. 1 engine under cover sub-assembly.



    A224743E01
  1. Unhook the No. 1 engine under cover sub-assembly from the frame as shown in the illustration.
    Text in Illustration 
    *a
    Hook
    *b
    Frame



3. REMOVE FRONT FENDER APRON SEAL LH


    A223333
  1. Remove the 5 clips and front fender apron seal LH from the front fender apron sub-assembly LH.



4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the service hole cover from the engine under cover.



    A070279E03
  1. Install a vinyl hose to the radiator drain cock on the radiator assembly side.
    Text in Illustration 
    *a
    Vinyl Hose
    *b
    Tape



  1. Fix the vinyl hose with tape.


    A307922E01


    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Reserve Tank Cap Sub-assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly and drain the engine coolant.

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the engine coolant from the engine.

    NOTICE:
    If engine coolant is not drained from the radiator drain cock plug, cylinder block drain cock plug and radiator reservoir, clogging in the radiator assembly or engine coolant leakage from the seal of water pump may result.



6. REMOVE BATTERY HOLD DOWN CLAMP


    A226647
  1. Loosen the 2 nuts and remove the battery hold down clamp.



7. REMOVE BATTERY


8. REMOVE BATTERY TRAY


9. REMOVE V-BANK COVER


    A229925E02
  1. Raise the front of the V-bank cover to disengage the 2 pins.
    Text in Illustration 
    *1
    Pin
    *2
    Hook
    *3
    No. 1 V-bank Cover Bracket

  1. Disengage the 2 hooks and remove the V-bank cover from the No. 1 V-bank cover bracket.



10. REMOVE AIR CLEANER CAP AND HOSE


    A227193
  1. Disconnect the MAF meter connector.

  1. Disengage the 4 wire harness clamps.

  1. Disconnect the ventilation hose and vacuum hose.

  1. Remove the bolt.

  1. Loosen the No. 1 air cleaner hose clamp.

  1. Release the 4 hinges.

  1. Remove the air cleaner cap and hose.



11. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.



12. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A226753
  1. Remove the 3 bolts and the air cleaner case sub-assembly.



13. REMOVE UPPER RADIATOR SUPPORT SEAL


    A226630
  1. Disengage the 7 clips and remove the upper radiator support seal from the fan shroud.



14. REMOVE FAN SHROUD


    A289174
  1. Disconnect the radiator reserve tank hose from the radiator assembly.



    A226632
  1. Loosen the 4 nuts holding the fan and fluid coupling assembly.



    A217571
  1. While turning the V-ribbed belt tensioner assembly counterclockwise, align the service hole for the V-ribbed belt tensioner assembly and the V-ribbed belt tensioner assembly fixing position, and then insert a bar of φ 6 mm (0.236 in.) into the service hole to fix the V-ribbed belt tensioner assembly in place.

    HINT:
    The pulley bolt for the V-ribbed belt tensioner assembly has a left-hand thread.

  1. Remove the fan and generator V belt.



    A287966E01
  1. Disengage the clamp and disconnect the 2 oil cooler hoses from the hose clamp.
    Text in Illustration 
    *1
    Oil Cooler Hose

  1. Remove the bolt and separate the radiator reserve tank assembly from the radiator assembly.

  1. Remove the 2 bolts and separate the fan shroud from the radiator assembly.

  1. Disengage the 2 guides of the fan shroud from the radiator assembly as shown in the illustration.

  1. Remove the 4 nuts of the fan and fluid coupling assembly, and then remove the fan shroud together with the fan and fluid coupling assembly.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump assembly.



15. DISCONNECT NO. 1 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


    A244710
  1. Loosen the hose clip and disconnect the No. 1 air injection system hose from the air hose assembly.



16. REMOVE AIR HOSE ASSEMBLY (w/ Secondary Air Injection System)


    A221459
  1. Remove the bolt and disconnect the air hose assembly from the timing chain cover sub-assembly.

  1. Loosen the hose clip and disconnect the air hose assembly from the No. 1 emission control valve set.



    A221458
  1. Remove the 2 bolts and disconnect the air hose assembly from the timing chain cover sub-assembly and No. 1 surge tank stay.

  1. Loosen the hose clip and remove the air hose assembly from the No. 2 emission control valve set.



17. REMOVE INTAKE AIR SURGE TANK


    A221456
  1. Disconnect the throttle with motor body assembly connector.

  1. Loosen the 2 hose clips and disconnect the No. 4 water by-pass hose and No. 5 water by-pass hose from the water inlet housing.



    A221464
  1. Disconnect the 2 clamps of the heater water hose from the intake air surge tank.



    A226749
  1. Loosen the hose clip and disconnect the No. 1 fuel vapor feed hose from the vacuum switching valve.

  1. Disconnect the No. 1 vacuum switching valve connector.



    A226750
  1. Loosen the hose clip and disconnect the No. 1 ventilation hose from the intake air surge tank.



    A244712
  1. Remove the bolt and disconnect the wire harness clamp bracket from the No. 2 surge tank stay.

  1. Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank.



    A221461
  1. Disengage the clamp and disconnect the wire harness from the No. 1 surge tank stay.



    A221462
  1. Remove the 2 bolts and No. 1 surge tank stay from the intake air surge tank.



    A221460
  1. Remove the 2 bolts and throttle body bracket from the intake air surge tank.



    A221465E06
  1. Using an 8 mm socket hexagon wrench, remove the 4 bolts, 2 nuts and intake air surge tank from the intake manifold.
    Text in Illustration 
    *1
    Nut

  1. Remove the air surge tank to intake manifold gasket from the intake air surge tank.



18. REMOVE AIR TUBE (w/ Secondary Air Injection System)


    A288091
  1. Remove the 2 bolts, 2 nuts and the air tube from the emission control valve set and exhaust manifold sub-assembly RH.

  1. Remove the 2 gaskets from the air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



19. REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)


    A230693
  1. Remove the 2 bolts, 2 nuts and the No. 2 air tube from the No. 2 emission control valve set and exhaust manifold sub-assembly LH.

  1. Remove the 2 gaskets from the No. 2 air tube.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



20. REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)


    A223568
  1. Disconnect the emission control valve set connector.

  1. Loosen the hose clamp and disconnect the air hose assembly from the emission control valve set.



    A223570
  1. Remove the 3 nuts and the emission control valve set from the cylinder head cover sub-assembly.



21. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)


    A223562
  1. Disconnect the No. 2 emission control valve set connector.

  1. Loosen the hose clamp and disconnect the air hose assembly from the No. 2 emission control valve set.



    A223564
  1. Remove the 3 nuts and the No. 2 emission control valve set from the cylinder head cover sub-assembly LH.



22. REMOVE IGNITION COIL ASSEMBLY


    A226756
  1. Disconnect the 6 ignition coil assembly connectors.

  1. Remove the 6 bolts and the 6 ignition coil assemblies from the cylinder head cover sub-assembly.



23. SEPARATE VANE PUMP ASSEMBLY


A225904
  1. Disconnect the 2 clamps and vane pump connector.

  1. Remove the 2 bolts and separate the vane pump.



24. REMOVE WIRING HARNESS CLAMP BRACKET


    A226648
  1. Disconnect the clamp.

  1. Remove the bolt and wire harness clamp bracket.



25. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A171090
  1. Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold sub-assembly LH.



26. REMOVE GENERATOR ASSEMBLY


    A222881
  1. Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.



    A222884
  1. Remove the 2 bolts and disconnect the wire harness.



    A222882
  1. Disconnect the wire harness clamp.

  1. Remove the bolt and disconnect the generator bracket from the cylinder block.



    A222883
  1. Remove the 2 bolts and generator assembly.



    A222885
  1. Remove the bolt and generator bracket.



27. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


A222114
  1. Remove the engine oil level dipstick from the engine oil level dipstick guide.

  1. Remove the bolt and engine oil level dipstick guide from the timing chain cover sub-assembly and guide hole.

  1. Remove the O-ring from the engine oil level dipstick guide.



28. REMOVE NO. 1 OIL PIPE


A223691
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe from the cylinder head cover sub-assembly LH and cylinder head LH.

  1. Remove the oil control valve filter LH and gaskets from the oil pipe union.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



29. REMOVE NO. 2 OIL PIPE


A223692
  1. Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe from the cylinder head cover sub-assembly and cylinder head sub-assembly.

  1. Remove the oil control valve filter RH and gaskets from the oil pipe union.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



30. REMOVE REAR CYLINDER HEAD COVER


    A224695
  1. Remove the 3 bolts and cover.



31. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe from the cylinder head cover sub-assembly LH.



32. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A226542E01
  1. Remove the 12 bolts, seal washer and cylinder head cover sub-assembly LH from the camshaft housing sub-assembly LH and timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Seal Washer

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. Remove the No. 2 cylinder head cover gasket from the cylinder head cover sub-assembly LH.



    A223665
  1. Remove the 3 gaskets from the camshaft bearing caps.



33. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A226543E01
  1. Remove the 12 bolts, seal washer and cylinder head cover sub-assembly from the camshaft housing sub-assembly RH and timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Seal Washer

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.



    A221164
  1. Remove the 3 gaskets from the camshaft bearing caps.



34. REMOVE TIMING CHAIN COVER PLATE


A224737
  1. Remove the 4 bolts, timing chain cover plate and gasket from the timing chain cover sub-assembly.



35. SET NO. 1 CYLINDER TO TDC/COMPRESSION


A072945E01
  1. Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover sub-assembly.



    A224754E02
  1. Check that the timing marks of the camshaft timing gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.
    Text in Illustration 
    *a
    for Bank 2
    *b
    for Bank 1
    *c
    Paint Mark

    HINT:
    If the marks are not aligned, turn the crankshaft again to align the marks.

  1. Place paint marks on the timing marks and sprockets of each camshaft timing gear assembly and on the links of the chain sub-assembly.

    HINT:
    Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gear assemblies at the locations of the timing marks of the camshaft timing gear assemblies.



36. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


A226510E01
  1. Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain sub-assembly.

    HINT:
    This prevents the valves and pistons from interfering with each other.



    A226547E02
  1. Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of φ1.27 mm (0.0500 in.) into the hole.
    Text in Illustration 
    *1
    Lever Hole
    *2
    Tensioner Hole



    A072945E01
  1. Turn the crankshaft clockwise, and align the notch with the timing mark "0" of the timing chain cover sub-assembly.



    A224739
  1. Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head.

    NOTICE:
    Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover sub-assembly.



37. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)


A226507E01
  1. Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain sub-assembly between the banks.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.

    CAUTION:
    As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gear assemblies.



    A226508E07
  1. Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be removed easily.

    HINT:
    When turning the crankshaft, engine oil may spray out of the oil holes.



    A224759
  1. Remove the chain sub-assembly from the sprocket of the camshaft timing gear assembly and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain sub-assembly and lift it upward to remove it from the sprocket.



38. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


A225726E01
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.
    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.



39. REMOVE NO. 2 CAMSHAFT


A224761
  1. Remove the bolt of the No. 2 chain tensioner assembly.



    A224769
  1. Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.



    A224763
  1. While lifting up the No. 2 camshaft, pass it through the No. 2 chain sub-assembly and pull it out towards the front of the vehicle to remove it.



40. REMOVE CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.



    A224767
  1. Remove the chain sub-assembly from the camshaft timing gear assembly and pull out the No. 2 camshaft and No. 2 chain sub-assembly towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain sub-assembly into the gap between the cylinder head sub-assembly and timing chain cover sub-assembly.



    A224765
  1. Suspend the chain sub-assembly with a string or equivalent.



41. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)


A072945E01
  1. Turn the crankshaft counterclockwise, and align the notch with the "0" timing mark of the timing chain cover sub-assembly.



    A224760
  1. Remove the chain sub-assembly from the sprocket of the camshaft timing gear assembly and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain sub-assembly and lift it upward to remove it from the sprocket.



42. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


A225727E01
  1. Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install replacement bolts and washers in the order shown in the illustration.
    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Replacement Bolt and Washer Installation

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number for replacement bolts: 91551-G0845 (8 bolts)
    3. Part number for replacement washers: 90201- 12028 (16 washers)

    NOTICE:
    1. Do not install the bearing caps when installing replacement bolts and washers.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow replacement bolts or washers to contact the camshaft.
    4. Do not drop replacement bolts or washers into the cylinder head.



43. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY


A224762
  1. Remove the bolt of the No. 3 chain tensioner assembly.



    A224770
  1. Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft sub-assembly.



    A224764
  1. While lifting up the No. 4 camshaft, pass it through the No. 2 chain sub-assembly and pull it out towards the front of the vehicle to remove it.



44. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
  1. Lift up the rear of the camshaft so that it is at an angle.



    A224768
  1. Remove the chain sub-assembly from the camshaft timing gear assembly and pull out the No. 3 camshaft sub-assembly and No. 2 chain sub-assembly towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.



    A224766
  1. Suspend the chain with a string or equivalent.



45. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227959E06
  1. Remove the flange bolt and camshaft timing gear assembly from the camshaft.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.



46. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227960E06
  1. Remove the flange bolt and camshaft timing exhaust gear assembly from the camshaft.
    Text in Illustration 
    *1
    Straight Pin
    *2
    Flange Bolt
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.