Home › ENGINE · 2TR-FE › CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A115870E01
  1. Using SST and a press, press in a new bearing.

    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)



    A115871E01
  1. Align the claws of the bearing retainer with the grooves inside the drive end frame.

  1. Install the bearing retainer with the 4 screws.



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the rotor and washer to the drive end frame.

  1. Install the generator washer to the generator rotor assembly.



3. INSTALL GENERATOR COIL ASSEMBLY


    A102584E01
  1. Using deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.



    A102577
  1. Install the generator coil assembly with the 4 through bolts.

    Torque:
    5.8 N*m{ 59 kgf*cm , 51 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A113845E01
  1. While pushing the 2 brushes to the inside of the generator brush holder assembly, insert a φ1.0 mm (0.039 in.) pin into the generator brush holder hole.



    A079316E01
  1. Install the brush holder assembly with the 2 screws.

  1. Pull out the pin from the brush holder assembly.



5. INSTALL TERMINAL INSULATOR


    A102585
  1. Install the terminal insulator.



6. INSTALL GENERATOR REAR END COVER


    A102574
  1. Install the end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }



7. INSTALL GENERATOR WITH CLUTCH PULLEY (w/ Clutch Pulley)


    A113834E01
  1. Set SST (A) and (B).

    SST
    09820-63020  

    1. Mount SST (A) in a vise.



    A102935E01
  1. Install the generator on SST (A) as shown in the illustration.

  1. Turn SST (B) counterclockwise, and tighten the generator pulley.

    SST
    09820-63020  

    Torque:
    87 N*m{ 891 kgf*cm , 64 ft.*lbf }

    NOTICE:
    Use a torque wrench with a fulcrum length of 380 mm (14.96 in.)

  1. Remove the generator from the SST.

    NOTICE:
    Check that the generator pulley rotates smoothly.

  1. Install a new generator pulley cap.



8. INSTALL GENERATOR PULLEY (w/o Clutch Pulley)


    A075664E01
  1. Install the generator pulley to the generator rotor shaft by tightening the generator pulley nut by hand.

  1. Hold SST (1-A) with a torque wrench, and tighten SST (1-B) clockwise to the specified torque.

    SST
    09820-63010   (09820-06010, 09820-06020)
    HINT: 
    SST (1-A) and (1-B)
    09820-06010
    SST 2
    09820-06020

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that the SST is secured to the generator rotor shaft.



    A075665E01
  1. Mount SST 2 in a vise.

  1. Insert SST (1-A) and (1-B) into SST 2, and attach the generator pulley nut to SST 2.



    A075686E01
  1. Tighten the generator pulley nut by turning SST (1-A) in the direction shown in the illustration.

    Torque:
    110 N*m{ 1,125 kgf*cm , 81 ft.*lbf }

  1. Remove the generator from SST 2.



    A075667E01
  1. Turn SST (1-B), and remove SST (1-A) and (1-B).

  1. Turn the generator pulley, and check that the generator pulley moves smoothly.