Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. SEPARATE FRONT SPEED SENSOR (w/ ABS)


    C102281E01
  1. Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.



3. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY


    C102283E01
  1. Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.



4. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.



    C102285E01
  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Do not damage the brake dust cover.
    3. Make sure that the string of the SST is securely tied to the vehicle.



5. REMOVE FRONT AXLE ASSEMBLY


    C102287
  1. Remove the 4 bolts, 4 nuts and front axle assembly from the front suspension lower arm.

  1. Remove the cotter pin and castle nut.



    C102660E01
  1. Using SST, remove the front axle assembly from the front suspension upper arm.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.
    3. Make sure that the string of the SST is securely tied to the vehicle.



6. REMOVE FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Remove the cotter pin.

  1. Loosen the nut.



    C103882E01
  1. Use SST to separate the front lower ball joint assembly from the steering knuckle.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.

  1. Remove the nut and front lower ball joint assembly.



7. REMOVE STEERING KNUCKLE


    C103883E01
  1. Remove the 4 bolts.



    C103880E01
  1. Using SST, remove the steering knuckle, brake dust cover from the front axle hub sub-assembly.

    SST
    09950-40011   (09951-04020, 09953-04010, 09952-04010, 09955-04051)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt (09953-04010) before use.



8. REMOVE FRONT WHEEL ADJUSTING NUT (w/ ABS)


    C103639E01
  1. Using SST and a hammer, release the staked part of the front wheel adjusting nut.

    SST
    09930-00010  

    NOTICE:
    Release the staked part of the nut completely, otherwise the threads of the front axle hub may be damaged.

  1. Hold the axle hub and bearing assembly in a vise between aluminium plates.

    NOTICE:
    Do not overtighten the vise.



    C102292E01
  1. Using SST, remove the front wheel adjusting nut and skid control rotor.

    SST
    09318-12010  



9. REMOVE FRONT WHEEL ADJUSTING NUT (w/o ABS)


    C111783E01
  1. Using SST and a hammer, release the staked part of the front wheel adjusting nut.

    SST
    09930-00010  

    NOTICE:
    Release the staked part of the nut completely, otherwise the threads of the front axle hub may be damaged.

  1. Hold the axle hub and bearing assembly in a vise between aluminium plates.

    NOTICE:
    Do not overtighten the vise.



    C111781E01
  1. Using SST, remove the front wheel adjusting nut and front wheel bearing dust deflector No.1.

    SST
    09318-12010  



10. REMOVE FRONT DISC


    C102293E01
  1. Remove the 6 bolts.



    C113549E01
  1. Remove the front disc as shown in the illustration.



11. REMOVE FRONT AXLE HUB BEARING


    C103489E01
  1. Using SST and a press, remove the front axle hub bearing.

    SST
    09555-55010  
    09950-60010   (09951-00480)
    09950-70010   (09951-07100)