Home › TRANSMISSION ยท R351 MANUAL TRANSMISSION › 2KD-FTV MANUAL TRANSMISSION ASSEMBLY

2KD-FTV MANUAL TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install the drain plug with a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



3. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for Long Wheelbase)
  1. Remove the 4 bolts, 2 nuts and 2 compression springs. 2 gasket and exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front and 2 gaskets.



4. REMOVE EXHAUST PIPE ASSEMBLY FRONT (for Super Long Wheelbase)
  1. Remove the 4 bolts, 2 nuts, 2 compression springs. exhaust pipe assembly front and 2 gaskets.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front and 2 gaskets.



5. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  



6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.



    C107214
  1. Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  



7. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


    C102206E01
  1. Put matchmarks on the control cable assembly and the outer lever.

  1. Remove the 2 nuts and separate the transmission control cable from the outer lever.



    C102219
  1. Using a screwdriver, disengage the claws of the 2 clips.

  1. Remove the transmission control cable and 2 clips from the transmission control cable bracket No.1.



8. DISCONNECT WIRE HARNESS


    C112961
  1. Disconnect the 2 connectors and clamps.



    C103903
  1. Separate the wire harness clamp from the manual transmission.

  1. Remove the 2 bolts and separate the ground cable.



9. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


    C102217
  1. Remove the 2 bolts and separate the clutch release cylinder



10. REMOVE STARTER ASSEMBLY (for 2.0kW Type)


    A113410E01
  1. Remove the bolt, then remove the ground cable.



    A115882E01
  1. Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.



    A115883E01
  1. Remove the bolt and 2 nuts, then remove the starter.



11. REMOVE STARTER ASSEMBLY (for 2.7kW Type)


    A113410E01
  1. Remove the bolt, then disconnect the ground cable.



    A115882E01
  1. Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.



    A115883E01
  1. Remove the bolt and 2 nuts, then remove the starter.



12. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY


    C102222
  1. Support the manual transmission unit with a transmission jack.

  1. Remove the bolt, nut, and 2 washers, and then separate the transmission unit from the frame.



    C102610E01
  1. Remove the 9 bolts, manual transmission unit, control cable bracket No.1, rear end plate, and cylinder block insulator.

    HINT:
    1. The A bolts in the illustration tighten the control cable bracket together.
    1. The B bolts in the illustration tighten the rear end plate together.
    1. Bolt C in the illustration tightens the harness clamp bracket together.



13. REMOVE EXTENSION HOUSING DYNAMIC (MTM) DAMPER (WITH DYNAMIC DAMPER)


    C112965
  1. Remove the 4 bolts and extension housing dynamic (MTM) damper.



14. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY


    C103476
  1. Remove the 4 bolts and rear engine mounting insulator assembly.