Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEELS


2. DRAIN DIFFERENTIAL OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.



3. DRAIN BRAKE FLUID


4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLIES


    C102597E01
  1. Release the parking brake lever, and remove the brake drum.

    HINT:
    If the brake drum cannot be removed easily, perform the following steps.

  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.



5. REMOVE REAR AXLE BRAKE DRUM GASKETS


6. REMOVE AUTOMATIC ADJUST LEVER LH


    C102605
  1. Remove the automatic adjust lever and the tension spring.



7. REMOVE AUTOMATIC ADJUST LEVER RH

HINT:
Removal procedure of the RH side is the same as that of the LH side.



8. SEPARATE PARKING BRAKE SHOE STRUT SET LH


    C102599E01
  1. Using SST, remove the upper side tension spring from the brake shoe.

    SST
    09703-30011  



9. SEPARATE PARKING BRAKE SHOE STRUT SET RH

HINT:
Removal procedure of the RH side is the same as that of the LH side.



10. REMOVE FRONT BRAKE SHOES


    C102600
  1. Using a needle-nose pliers, remove the anchor side tension spring.



    C102601E01
  1. Using SST, remove the cup, shoe hold-down sprig and pin.

    SST
    09718-00010  



    C102667
  1. Remove the parking brake shoe lower strut.

  1. Separate the brake shoe return spring, and remove the front brake shoe.



11. REMOVE REAR BRAKE SHOES


    C102603E01
  1. Using SST, remove the cup, shoe hold-down sprig and pin.

    SST
    09718-00010  



    C102606
  1. Disconnect the parking brake cable No.3 and remove the rear brake shoe.



12. REMOVE PARKING BRAKE SHOE STRUT SET LH


    C102607E01
  1. Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.

  1. Remove the adjusting bolt and tension spring from the brake shoe strut set.



13. REMOVE PARKING BRAKE SHOE STRUT SET RH

HINT:
Removal procedure of the RH side is the same as that of the LH side.



14. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.3


    C102159
  1. Remove the 2 bolts and separate the parking brake cable assembly No.3 from the rear brake backing plate.



15. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.2

HINT:
Removal procedure of the RH side is the same as that of the LH side.



16. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY LH


    C102608
  1. Using SST, disconnect the brake tube, use a container to catch brake fluid.

    SST
    09023-00101  

  1. Remove the 2 bolts and wheel cylinder.



17. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY RH

HINT:
Removal procedure of the RH side is the same as that of the LH side.



18. SEPARATE SPEED SENSOR REAR LH (w/ ABS)


    C102662E01
  1. Remove the bolt and separate the rear speed sensor.

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.

  1. Remove the O-ring from the rear speed sensor.



19. SEPARATE SPEED SENSOR REAR RH (w/ ABS)

HINT:
Removal procedure of the RH side is the same as that of the LH side.



20. REMOVE REAR AXLE SHAFT WITH BACKING PLATE LH


    C102664J01
  1. Remove the 4 nuts and rear axle shaft with backing plate.

    NOTICE:
    1. Be careful not to damage the rear axle shaft oil seal.
    2. Be careful not to damage the skid control rotor rear.



21. REMOVE REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Removal procedure of the RH side is the same as that of the LH side.



22. REMOVE BEARING RETAINER O-RINGS
  1. Remove the bearing retainer O-ring from the rear axle housing assembly.



23. REMOVE REAR AXLE SHAFT LH OIL SEAL


    C102232E01
  1. Using SST, remove the rear axle shaft oil seal from the rear axle housing assembly.

    SST
    09308-00010  



24. REMOVE REAR AXLE SHAFT RH OIL SEAL

HINT:
Removal procedure of the RH side is the same as that of the LH side.



25. REMOVE PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.



    C107214
  1. Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  



26. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  



27. DISCONNECT LOAD SENSING BRACKET


    C102254
  1. Remove the 2 nuts and load sensing bracket.



28. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY
  1. Support the differential carrier assembly with a jack.

    NOTICE:
    Do not drop the differential carrier assembly



    C030284E01
  1. Remove the 10 nuts, washers and differential carrier assembly.

    NOTICE:
    1. Do not damage the installation surface when removing the differential carrier assembly.
    2. The remaining oil may leak out when removing the differential carrier assembly.



29. REMOVE REAR DIFFERENTIAL CARRIER GASKET