Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL DUST DEFLECTOR


    C111770E01
  1. Using steel plate and a press, install a new dust deflector.

    NOTICE:
    1. Slowly press in the dust deflector.
    2. If any burrs remain after pressing in the deflector, remove them.



2. INSTALL REAR DIFFERENTIAL PINION SHAFT PIN


    ZK01881
  1. Install the 2 thrust No.1 washers to the 2 side gears.

    NOTICE:
    1. Make sure that there is no dirt or foreign matter on the thrust washer, side gear, etc. before installing them.
    2. If replacing either the side gear or pinion, replace them as a set.
    3. Apply hypoid gear oil API GL-5 to all sliding and rotating parts.



    ZK01882
  1. Install the 2 side gears, 2 differential pinion gears, 2 differential pinion thrust washers and differential pinion shaft to the differential case.

    NOTICE:
    Align the holes of the differential case and differential pinion shaft.

  1. Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    ZK01883
  1. Using a dial indicator, measure the side gear backlash while holding 1 pinion gear toward the differential case.

    Backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    If the backlash is not within the specified range, install the 2 side gear thrust No.1 washers of different thicknesses.

    HINT:
    Refer to the following table to select the 2 side gear thrust No.1 washers.

    Thrust No.1 washer thickness 
    Thickness mm (in.)
    1.57 to 1.63 (0.0618 to 0.0642)
    1.67 to 1.73 (0.0657 to 0.0681)
    1.77 to 1.83 (0.0697 to 0.0720)



    ZK01884
  1. Using a pin punch (5 mm) and a hammer, install the straight pin through the differential case and hole of the pinion shaft.



    ZK01885
  1. Using a chisel and a hammer, stake the outside of the differential case pin hole.



3. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Clean the differential ring gear set bolt hole.



    SA01143E01
  1. Heat the ring gear to approx. 100°C (212°F) in boiling water.

    CAUTION:
    Use thick gloves to protect hands as the ring gear is hot.

  1. Carefully take the ring gear out of the boiling water.

  1. Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.



    C103291E01
  1. Align the matchmarks on the ring gear and differential case.

  1. Temporarily install 5 new lock plates and 10 bolts.

  1. After the ring gear cools down, tighten the 10 bolts uniformly.

    Torque:
    97 N*m{ 985 kgf*cm , 72 ft.*lbf }

    HINT:
    Tighten the bolts in diagonal order little by little in several steps.



    C104915
  1. Using a chisel and a hammer, stake the 5 lock plates.

    1. Stake one claw so that it is flush against the flat surface of the bolt.

    2. Stake the other claw against the surface of the bolt head to act as a stopper if the bolt starts to loosen.



4. INSTALL REAR DIFFERENTIAL CASE BEARING


    C102938E01
  1. Using SST and a press, install the case bearing inner races LH and RH to the differential case.

    SST
    09950-60010   (09951-00480, 09951-00550)
    09950-70010   (09951-07150)

    NOTICE:
    1. Do not apply hypoid gear oil to a new bearing.
    2. Do not deform the bearing cage.
    3. Set the SST to the center of the differential case.
    4. If the bearing is replaced, replace it and the outer race as a set.



5. INSPECT DIFFERENTIAL RING GEAR RUNOUT
  1. Install the case bearing outer races LH and RH to the case bearing inner races LH and RH respectively.

    NOTICE:
    Be sure to install the bearing outer races in each correct position.



    C028220
  1. Install the differential case to the differential carrier.



    C028221
  1. Install the 2 bearing adjusting nuts.



    C111765E01
  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



    C014075
  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the drive pinion, ring gear and differential case.

  1. Remove the right and left bearing caps and differential case.



6. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C111771E01
  1. Using SST and a press, install the outer race of the rear drive pinion rear tapered roller bearing to the differential carrier.

    SST
    09316-60011   (09316-00011, 09316-00041)



7. INSTALL DIFFERENTIAL OIL STORAGE RING


    C116322E01
  1. Using SST and a press, install the oil storage ring to the differential carrier.

    SST
    09950-70010   (09951-07200)
    09950-60010   (09951-00590)



8. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C111772E01
  1. Using SST and a press, install the outer race of the rear drive pinion front tapered roller bearing to the differential carrier.

    SST
    09316-60011   (09316-00011, 09316-00021)



9. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING
  1. Install the drive pinion plate washer to the drive pinion.



    C111773E01
  1. Using SST and a press, install the inner race of the rear drive pinion rear tapered roller bearing to the drive pinion.

    SST
    09506-30012  



10. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


    C028218
  1. Install the drive pinion and the inner race of the rear drive pinion front tapered roller bearing and oil slinger to the differential carrier.



    C111774E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.

  1. Coat the threads of the drive pinion nut with hypoid gear oil LSD.



    C111775E01
  1. Using SST, hold the flange.

    SST
    09330-00021  

  1. Using a socket wrench (30 mm) and torque wrench, temporarily tighten the drive pinion nut.

    Torque:
    370 N*m (3,770 kgf*cm, 273 ft.*lbf) or less

    NOTICE:
    As there is no bearing spacer, tighten the nut a little at a time and do not overtighten.

  1. Turn the bearing clockwise and counterclockwise several times to stabilize it.



    C003092
  1. Using a socket wrench (30 mm) and torque wrench, measure the preload.

    Drive pinion preload (at starting):
    New bearing:
    1.05 to 1.64 N*m (11.0 to 17.0 kgf*cm, 9.0 to 15.0 in.*lbf)
    Reused bearing:
    0.56 to 0.85 N*m (6.0 to 9.0 kgf*cm, 5.0 to 8.0 in.*lbf)

    NOTICE:
    Record the preload for total preload measurement.

    If the preload is not within the specified range, adjust the differential drive pinion preload or repair as necessary.



11. INSTALL DIFFERENTIAL CASE ASSEMBLY
  1. Install the case bearing outer races LH and RH to the case bearing inner races LH and RH respectively.

    NOTICE:
    Be sure to install the bearing outer races in each correct position.



    C028220
  1. Install the differential case to the differential carrier.

    HINT:
    Make sure the right and left races are not interchanged.



12. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT


    C028221
  1. Install the 2 bearing adjusting nuts into the differential carrier, making sure the nuts are threaded properly.



    C111765E01
  1. Align the matchmarks on the bearing cap and differential carrier.

  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

    HINT:
    If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly. Reinstall the adjusting nuts if necessary.



13. ADJUST DIFFERENTIAL RING GEAR BACKLASH


    C111776E01
  1. Tighten the 4 bearing cap bolts to the specified torque, then loosen them to the point where the adjusting nuts can be turned by SST.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. Using the SST and dial indicator, tighten the adjusting nut on the ring gear back surface side so that the backlash of the ring is about 0.18 mm (0.0071 in.).

    SST
    09504-00011  



    C111777E01
  1. While turning the ring gear, use the SST to fully tighten the adjusting nut on the ring gear tooth side. After the bearings have settled, loosen the adjusting nut on the ring gear tooth side.

    SST
    09504-00011  

  1. Using SST, torque the adjusting nut 1.5 notches from the 0 preload position.



    C112603E01
  1. Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    HINT:
    The backlash is adjusted by turning the left and right adjusting nuts by an equal amounts. For example, loosen the nut on the right side by one notch.



    C111765E01
  1. Torque the 4 bearing cap bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



14. INSPECT TOTAL PRELOAD


    C003092
  1. Using a socket wrench (30 mm) and torque wrench, measure the preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)

    If the preload is not within the specified range, adjust it by the bearing adjusting nut on the ring gear teeth side.



15. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION


    C014071
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead primer.

  1. Rotate the ring gear in both directions.



  1. Inspect the tooth contact pattern.


    SA01653E01



    C112001E01
  1. If the teeth are not contacting properly, use the following table to select a proper washer for correction.
    Plate washer thickness 
    Thickness mm (in.)
    Thickness mm (in.)
    1.69 to 1.71 (0.0665 to 0.0673)
    2.02 to 2.04 (0.0795 to 0.0803)
    1.72 to 1.74 (0.0677 to 0.0685)
    2.05 to 2.07 (0.0807 to 0.0815)
    1.75 to 1.77 (0.0689 to 0.0697)
    2.08 to 2.10 (0.0819 to 0.0827)
    1.78 to 1.80 (0.0701 to 0.0709)
    2.11 to 2.13 (0.0831 to 0.0839)
    1.81 to 1.83 (0.0713 to 0.0720)
    2.14 to 2.16 (0.0843 to 0.0850)
    1.84 to 1.86 (0.0724 to 0.0732)
    2.17 to 2.19 (0.0854 to 0.0862)
    1.87 to 1.89 (0.0736 to 0.0744)
    2.20 to 2.22 (0.0866 to 0.0874)
    1.90 to 1.92 (0.0748 to 0.0756)
    2.23 to 2.25 (0.0878 to 0.0886)
    1.93 to 1.95 (0.0760 to 0.0768)
    2.26 to 2.28 (0.0890 to 0.0898)
    1.96 to 1.98 (0.0772 to 0.0780)
    2.29 to 2.31 (0.0902 to 0.0909)
    1.99 to 2.01 (0.0783 to 0.0791)
    2.32 to 2.34 (0.0913 to 0.0921)



16. REMOVE REAR DRIVE PINION NUT


17. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


18. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


20. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    C093601
  1. Install a new drive pinion bearing spacer to the drive pinion.

    NOTICE:
    Be sure to face the larger inner diameter side rearward as shown in the illustration.



21. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


22. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


23. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C111779E01
  1. Using SST and a hammer, install a new oil seal.

    SST
    09554-22010  

    Oil seal drive in depth:
    0.55 to 1.45 mm (0.0217 to 0.0571 in.)

  1. Apply MP grease to the oil seal lip.



24. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C111780E01
  1. Using SST, install the companion flange to the drive pinion.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.

  1. Coat the threads of a new drive pinion nut with hypoid gear oil LSD.



    C111775E01
  1. Using SST, hold the flange.

    SST
    09330-00021  

  1. Using a socket wrench (30 mm) and torque wrench, temporarily tighten the drive pinion nut.

    Torque:
    370 N*m (3,770 kgf*cm, 273 ft.*lbf) or less



25. INSPECT DRIVE PINION PRELOAD


    SA02352
  1. Turn the bearing clockwise and counterclockwise several times to stabilize it.

  1. Using a socket wrench (30 mm) and torque wrench, measure the preload.

    Preload (at starting):
    New bearing:
    1.05 to 1.64 N*m (11.0 to 17.0 kgf*cm, 9.0 to 15.0 in.*lbf)
    Reused bearing:
    0.56 to 0.85 N*m (6.0 to 9.0 kgf*cm, 5.0 to 8.0 in.*lbf)

  1. If the preload is less than the specified minimum value, check the preload while retightening the drive pinion nut by 5 to 10°to adjust it into the specified range.

  1. If the preload is less than the specified minimum value even when the tightening torque of the drive pinion nut is greater than the specified maximum value, loosen the nut and check that the threads of the drive pinion nut and drive pinion are not stripped.

  1. If the threads are not stripped, replace the bearing spacer. Apply hypoid gear oil LSD to the threads of the drive pinion and repeat the procedure.



26. INSPECT TOTAL PRELOAD


    SA02352
  1. Using a socket wrench (30 mm) and torque wrench, measure the preload.

    Total preload (at starting):
    Drive pinion preload plus 0.39 to 0.59 N*m (4.0 to 6.0 kgf*cm, 3.5 to 5.2 in.*lbf)



27. INSPECT DIFFERENTIAL RING GEAR BACKLASH
  1. Set the dial indicator to the end of the differential ring gear face.



    C028211
  1. Rotate the differential ring gear and measure the backlash.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)



28. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    F001237E01
  1. Using a dial indicator, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    0.09 mm (0.0035 in.)

    If the runout is greater than the maximum value, replace the companion flange sub-assembly.



29. INSTALL REAR DRIVE PINION NUT


    ZK07449
  1. Using a chisel and hammer, stake the drive pinion nut.



30. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


    C028226J01
  1. Install the 2 bearing adjusting nut locks to the bearing caps.

  1. Tighten both of the bearing adjusting nut locks with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }