Home › ENGINE ยท 2KD-FTV › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
(Click here)


2. REMOVE VANE PUMP ASSEMBLY


    C101372E01
  1. Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.



3. REMOVE TIMING BELT NO.1 COVER
  1. Remove the wire harness clamp.



    A102815
  1. Remove the 6 bolts and timing belt cover No.1.



4. REMOVE TIMING BELT


    A070549E01
  1. Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.



    A070550
  1. Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

  1. Remove the timing belt.



5. REMOVE FAN PULLEY
  1. Remove the 4 nuts and fan pulley.



6. REMOVE EGR PIPE SUB-ASSEMBLY NO.1.


    A106043
  1. Disconnect the fuel pressure sensor connector.



    A106844
  1. Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.



7. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and oil level gauge guide.



8. REMOVE INJECTION PIPE
SST
09023-12701  


  1. Remove the injection pipe.



      A103526
    1. Remove the 2 nuts and injection pipe clamp No.3.



    2. A103532
    3. Using SST, remove the 4 injection pipes.

      SST
      09023-12701  



9. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Using SST, remove the fuel inlet pipe sub-assembly.

    SST
    09023-12701  



10. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY


    A070710
  1. Remove the 4 bolts.

  1. Remove the camshaft timing pulley flange No.2 and pump drive shaft pulley.



    A077989
  1. Using SST, remove the supply pump gear set nut and O-ring while holding the crankshaft pulley.

    SST
    09213-58013  
    09330-00021  



    A076978
  1. Disconnect the 2 fuel hoses.

  1. Disconnect the 2 connectors and wire harness.

  1. Loosen the 2 nuts as shown in the illustration.



    A077990E01
  1. Using SST, disengage the supply pump from the supply pump gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

  1. Remove the 2 nuts and supply pump from the engine.

  1. Remove the O-ring from the supply pump.

  1. Remove the pulley key from the supply pump.



11. REMOVE COMPRESSOR BRACKET


    A102453E01
  1. Remove the 4 bolts and compressor bracket.



12. REMOVE IDLE PULLEY ASSEMBLY
  1. Remove the bolt, washers and idle pulley assembly.



13. REMOVE GENERATOR BRACKET
  1. Remove the 2 bolts and generator bracket.



14. REMOVE GENERATOR ASSEMBLY


    A113682E01
  1. Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and generator assembly.



15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Remove the 4 bolts and belt tensioner assembly.



16. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1


    A070696
  1. Using a 10 mm socket hexagonal wrench, remove the bolt, plate washer and timing belt idler No.1.



17. REMOVE CRANKSHAFT PULLEY


    A072413E01
  1. Remove the bolt holding the crankshaft with SST.

    SST
    09213-58013  
    09330-00021  

  1. Insert the service bolt.



    A072414E01
  1. Remove the crankshaft pulley with SST.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



18. REMOVE VACUUM PUMP ASSEMBLY


    C102554
  1. Slide the clip and disconnect the 2 vacuum hoses from the vacuum pump.

  1. Remove the union bolt, vacuum pump union and 2 gaskets.



    C102555
  1. Remove the 2 nuts and pull out the vacuum pump from the engine.

  1. Remove the 2 O-rings.



19. REMOVE CAMSHAFT POSITION SENSOR


    A102283
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.



20. REMOVE CRANKSHAFT POSITION SENSOR


    A102284
  1. Disconnect the crankshaft position sensor connector.

  1. Separate the connector from the vacuum pipe No.1.



    A102285
  1. Separate the 3 wire harness clamps.

  1. Remove the bolt and the crankshaft position sensor.



21. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.



22. REMOVE OIL FILLER CAP SUB-ASSEMBLY


    A074130
  1. Remove the oil filler cap from the cylinder head cover.



23. REMOVE NOZZLE HOLDER SEAL


    A100846
  1. Using a screwdriver, remove the holder seals by prying the portion between the holder seal and the cutout part of the cylinder head.



24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A051295E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.



25. REMOVE CAMSHAFT TIMING PULLEY


    A100848
  1. Remove the bolt for the camshaft timing pulley by holding the camshaft with a wrench.



    A115888E01
  1. Using SST, remove the camshaft timing pulley and set key.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)



    A100847E05
  1. Rotate the crankshaft about 90° counterclockwise from the TDC position to lower the piston.



26. REMOVE TIMING BELT NO.2 COVER


    A051300
  1. Remove the nut, 4 bolts and timing belt No.2 cover.



27. REMOVE WATER PUMP ASSEMBLY


    A100852
  1. Remove the 5 bolts, 2 nuts, water pump and gasket.



28. REMOVE TIMING GEAR CASE


    A100853
  1. Remove the 14 bolts and 2 nuts.



    A102800
  1. Pry the gear case in the location shown in the illustration.

    NOTICE:
    Do not damage the contact surface.



    A102771
  1. Secure the idler sub-gears to the idler gear with a service bolt.



    A102772
  1. Remove the supply pump gear.



    A103311E01
  1. Remove the O-ring.



29. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO.1


    A102774
  1. Remove the crankshaft position sensor plate.



30. REMOVE CRANKSHAFT TIMING GEAR


    A100863E01
  1. Using SST, remove the crankshaft timing gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



31. REMOVE IDLE GEAR THRUST PLATE


    A102775
  1. Remove the 2 bolts and thrust plate.



32. REMOVE IDLE GEAR NO.1


    A100860
  1. Turn the sub gear and align the gear teeth of the idle main gear and sub gear.

  1. Remove the idle gear and sub gear.



33. REMOVE IDLE GEAR SHAFT NO.1


    A102776
  1. Remove the idle gear shaft.



34. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


    A100854
  1. Using a screwdriver and hammer, tap out the oil seal.



35. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL


    A100856
  1. Using a screwdriver and hammer, tap out the oil seal.



36. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket.



    A074128E01
  1. Remove the 22 bolts and 2 nuts.



    Z004119E01
  1. Insert the blade of SST between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    SST
    09032-00100  

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Do not damage the oil pan flange.



37. REMOVE OIL STRAINER SUB-ASSEMBLY


    A102736
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.



38. REMOVE TIMING GEAR CASE ASSEMBLY


    A100878
  1. Remove the union bolt and 8 bolts.



    A102853E01
  1. Pry the gear case in the location shown in the illustration, remove the gear case.

    NOTICE:
    Do not drop the oil pump rotor.



    A051330
  1. Remove the driven rotor and gasket.



    A052300
  1. Remove the stud bolt.



    A102777
  1. Remove the 2 O-rings.