Home › BRAKE › BRAKE › LOAD SENSING PROPORTIONING VALVE

LOAD SENSING PROPORTIONING VALVE > INSTALLATION

for Preparation Click here



1. INSTALL LOAD SENSING W/SPRING VALVE ASSEMBLY


    C102563
  1. Install the load sensing with spring valve assembly with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Using SST, install the 3 brake tubes to the load sensing with spring valve assembly.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



    C102562
  1. Install the load sensing spring bracket with the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



2. ADD BRAKE FLUID


C106088

Fluid:
SAE J1704 or FMVSS No. 116 DOT3 or equivalent



3. BLEED BRAKE SYSTEM
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



4. INSPECT BRAKE FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No.116 DOT3 or equivalent



5. CHECK BRAKE FLUID LEAKAGE


6. RAISE FRONT BRAKE PRESSURE 9,807 kPa (100 kgf/cm2, 1,422 psi) AND CHECK REAR BRAKE PRESSURE

  1. C102558
  2. HINT:
    Gradually depress on the brake pedal until the pressure reaches the specified valve. Do not overshoot the specified pressure. Read the value of rear pressure 2 seconds after adjusting to the specified fluid pressure.


    Rear brake fluid pressure table:
    Standard body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    ***202R (L) - *E****
    5860 +- 800
    (60 +- 8, 850 +- 116)
    ***203R (L) - *E****
    5860 +- 800
    (60 +- 8, 850 +- 116)
    Others
    5860 +- 800
    (60 +- 8, 850 +- 116)
    Wide long body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    **H212R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    **H213R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    Wide super body type:
    Model
    Rear brake pressure
    kPa (kgf/cm2, psi)
    **H220R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    **H221R (L) - ******
    6600 +- 800
    (67 +- 8, 957 +- 116)
    Others
    6600 +- 800
    (67 +- 8, 957 +- 116)



7. IF NECESSARY, ADJUST FLUID PRESSURE


    C102559E01
  1. Adjust the length of the shackle.
    Lower pressure - Lengthen "A"
    High pressure - Shorten "A"

    Initial set:
    120 mm (4.72 in.)

    Adjusting:
    112 to 128 mm (4.40 to 5.04 in.)



    C102561
  1. If the pressure cannot be adjusted by the shackle, raise or lower the valve body.
    Lower pressure - Lower
    High pressure - Raise

  1. Torque the nuts.

    Torque:
    12.5 N*m (130 kgf*cm, 9 ft.*lbf)

  1. Adjust the length of the shackle again.
    If it cannot be adjusted, inspect the valve body.