BACK DOOR > DISASSEMBLY |
| 1. REMOVE OUTER UNDER REAR VIEW MIRROR ASSEMBLY (w/ Outer Under Rear View Mirror) |
![]() |
Remove the 3 screws, disengage the pin and remove the outer under rear view mirror.
| 2. REMOVE BACK DOOR SERVICE HOLE COVER |
| 3. REMOVE BACK DOOR TRIM BOARD ASSEMBLY UPPER (w/o Rear Wiper) |
![]() |
Disengage the 5 clips and remove the back door trim board assembly upper.
| 4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY UPPER (w/ Rear Wiper) |
![]() |
Disengage the 6 clips and remove the back door trim board assembly upper.
Remove the remaining clips on the body, and reinstall them to the back door trim board assembly upper.
| 5. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper) |
![]() |
Disengage the 3 claws and separate the head cap as shown in the illustration.
Remove the rear wiper arm nut and rear wiper arm and blade assembly.
| 6. REMOVE REAR WIPER SHAFT COVER (w/ Rear Wiper) |
![]() |
Remove the rear wiper shaft cover.
| 7. REMOVE REAR WIPER LINK PIVOT NO.1 WASHER (w/ Rear Wiper) |
![]() |
Using the socket wrench (27 mm), remove the lock nut and rear No.1 wiper link pivot washer.
| 8. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper) |
![]() |
Disconnect the connector and remove the clamp.
Remove the 3 bolts and rear wiper motor and grommet as a unit.
![]() |
Remove the grommet from the rear wiper motor.
| 9. REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY (w/ High Mounted Stop Light) |
![]() |
Disconnect the connector.
Disengage the 4 claws and remove the high mounted stop light assembly.
| 10. REMOVE BACK DOOR NO.3 WIRE |
Disconnect the connectors.
![]() |
Disengage the 2 clamps and remove the back door No.3 wire.
| 11. REMOVE REAR WINDOW NO.1 WIRE |
![]() |
Disengage the 2 clamps and remove the rear window No.1 wire.
| 12. REMOVE BACK DOOR INSIDE HANDLE (w/ Back Door Inside Handle) |
![]() |
Remove the screw and the back door inside handle.
| 13. REMOVE BACK DOOR INSIDE HANDLE BEZEL (w/ Back Door Inside Handle Bezel) |
![]() |
Remove the 2 screws and the back door inside handle bezel.
| 14. REMOVE BACK DOOR TRIM BOARD (DX Grade) |
![]() |
Using a clip remover, remove the 16 clips and the back door trim board.
| 15. REMOVE BACK DOOR TRIM BOARD (GL Grade) |
![]() |
Using a clip remover, remove the 18 clips and the back door trim board.
| 16. REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY (w/ Back Door Inside Handle) |
Disconnect the link.

Remove the 3 screws and the back door inside handle assembly.
| 17. REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY (w/o Power Door Lock) |
![]() |
Disconnect the wire and link.
Disengage the clamp.
Remove the screw and the back door remote control assembly.
| 18. REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY (w/ Power Door Lock) |
![]() |
Disconnect the wire and link.
Disengage the 2 clamps.
Remove the 3 screws and the back door remote control assembly.
| 19. REMOVE BACK DOOR OUTSIDE HANDLE |
![]() |
Remove the 2 nuts and the back door outside handle.
| 20. REMOVE BACK DOOR GARNISH OUTSIDE |
| 21. REMOVE BACK DOOR NO.2 WIRE |
![]() |
Remove the bolt.
Disengage the 6 clamps and remove the back door No.2 wire.
| 22. REMOVE BACK DOOR NO.1 WIRE |
| 23. REMOVE BACK DOOR STOPPER BRACKET SUB-ASSEMBLY (for Rough Road Area Spec.) |
![]() |
Remove the 2 bolts and the back door stopper bracket sub-assembly.
| 24. REMOVE BACK DOOR LOCK PROTECTOR (w/ Rear Bumper Step) |
![]() |
Remove the screw and the back door lock protector.
| 25. REMOVE BACK DOOR LOCK ASSEMBLY |
![]() |
Remove the 3 bolts and the back door lock assembly.
| 26. REMOVE BACK DOOR STOPPER LH |
![]() |
Remove the 2 bolts and the back door stopper LH.
| 27. REMOVE BACK DOOR STOPPER RH |
| 28. REMOVE BACK DOOR STAY ASSEMBLY LH |
![]() |
Remove the 4 bolts and the back door stay assembly LH.
| 29. REMOVE BACK DOOR STAY ASSEMBLY RH |