Home › ENGINE ยท 2KD-FTV › FUEL › COMMON RAIL

COMMON RAIL > INSTALLATION

for Preparation Click here



1. INSTALL COMMON RAIL ASSEMBLY


    A102476E01
  1. Install the common rail assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the fuel hose to the fuel pressure limiter.

  1. Connect the fuel pressure sensor connector.



2. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY NO.2


    A103527
  1. Temporarily install the nozzle leakage pipe assembly No.2 with the 2 bolts.



    A103528
  1. Install the check valve nozzle leakage pipe assembly No.2 and a new gasket.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A103533
  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A103529
  1. Install the 3 fuel hoses on the nozzle leakage pipe assembly No.2.



3. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
  1. Also, if the supply pump is replaced, the fuel inlet pipe must be replaced.
  2. Be careful not to adhere dusts, dirt or any other materials onto the joint area of the fuel inlet pipe.

  1. Temporarily install the fuel inlet pipe.

  1. Using SST, tighten the injection pipe on the common rail side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST

  1. Using SST, tighten the injection pipe on the supply pump side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST



4. INSTALL INJECTION PIPE
SST
09023-12701  

NOTICE:
  1. When replacing the injector replace the injection pipe as well.
  2. Keep clean the joint of the injection pipe.



  1. Install the injection pipes.



      A103532
    1. Temporarily install the 4 injection pipes.



    2. A103526
    3. Install the injection pipe clamp No.3 in 2 nuts.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    4. A103532E01
    5. Fasten the union sequentially, from the injection pipe common rail to the injector, using SST.

      SST
      09023-12701  

      Torque:
      Use union nut wrench and torque wrench:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }



5. INSTALL OIL LEVEL GAGE GUIDE
  1. Install a new O-ring to the oil level gauge guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the oil level gauge guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the oil level gauge.



6. INSTALL INTAKE AIR CONNECTOR (w/o EGR Valve)


    A106848E01
  1. Temporarily install 2 new gaskets and intake air connector No.2 to the intake air connector.



    A106846
  1. Temporarily tighten the intake air connector assembly with the bolt and 2 nuts.

  1. Tighten the manifold stay with the bolt.

  1. Tighten the intake air connector with the bolt and 2 nuts.

  1. Install the vacuum hose to the intake air connector.



7. TEMPORARILY TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)


  1. Temporarily tighten the EGR valve assembly with the sensor.



      A115761E01
    1. Install 2 new gaskets and the EGR valve to the intake air connector as shown in the illustration.



    2. A102287
    3. Temporarily tighten the intake air connector with EGR valve assembly to the intake manifold with the bolt and the 2 nuts.

    4. Install the vacuum hose to the intake air connector.

    5. Temporarily tighten the manifold stay with the bolt.



    6. A103043
    7. Connect the EGR valve position sensor connector.

    8. Connect the intake air temperature sensor connector.



  1. Install the vacuum regulating valve.



      A103046
    1. Install the vacuum regulating valve with the 2 bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Connect the 2 vacuum hoses and the regulating valve connector.



8. INSTALL EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)


    A106845
  1. Install the 2 gaskets to the cylinder head and EGR pipe sub-assembly as shown in the illustration.



    A106844
  1. Install the EGR pipe sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the intake air connector with the bolt and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the manifold stay.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



9. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)
  1. Remove the 3 bolts, the 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.



10. INSTALL DIESEL THROTTLE BODY ASSEMBLY

NOTICE:
After removing and installing, or replacing the throttle body, be sure to perform the operation check.

  1. Install a new gasket to intake air connector.



    A102902
  1. Install the throttle body with the 2 bolts and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A102282
  1. Connect the 2 throttle body connectors.



11. INSTALL AIR HOSE NO.4


    A102281
  1. Install the air hose No.4 with the 2 clamps.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



12. INSTALL EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)


    A106845
  1. Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.



    A106844
  1. Install the EGR pipe with the 2 bolts and the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A106043
  1. Connect the fuel pressure sensor connector.



13. INSTALL OIL RETURN HOSE (w/ Inter Cooler)


    A106042
  1. Connect the oil return hose with the clip.



14. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY


    A102278
  1. Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



15. INSTALL ENGINE SERVICE HOLE COVER NO.2
  1. Install the engine service hole cover No.2 with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A113039
  1. Return the carpet.



16. CONNECT BATTERY NEGATIVE CABLE
  1. Install the engine service hole cover No.2 with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A113039
  1. Return the carpet.



17. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs and fill the radiator reserve tank assembly with coolant to the top of the inlet.

  1. Loosen the bleeder plug of outlet housing.

  1. When air is bled and the coolant drains out, firmly install the bleeder plug.

  1. Add coolant up to the B line mark in the radiator reserve tank assembly and install the radiator cap.

    Coolant capacity:
    Condition
    Capacity
    w/ rear heater
    17.0 liters (18.0 US qts, 15.0 imp. qts)
    w/o rear heater
    15.0 liters (15.9 US qts, 13.2 imp. qts)

  1. Warm up the engine.

  1. After the engine cools down check that the coolant level is between the LOW and FULL level marks.



18. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



19. BLEED FUEL LINE


    A114068E01
  1. Using the hand pump, bleed air from the fuel system until pumping becomes difficult.



20. CHECK FOR FUEL LEAKAGE
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECD / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
      2. Above conditions preserved while test is ON