Home › ENGINE ยท 2KD-FTV › FUEL › FUEL TEMPERATURE SENSOR

FUEL TEMPERATURE SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TEMPERATURE SENSOR


    A078244E01
  1. Apply a light coat of light oil to a new O-ring.

  1. Install the O-ring to the fuel temperature sensor.

  1. Using the SST, install the fuel temperature sensor.

    SST
    09922-10010  

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }



2. INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY


    A070715
  1. Confirm that the supply pump gear in the timing gear case moves back and forth smoothly.

  1. Install a new O-ring and the pulley key to the supply pump.

  1. Aligning the projecting edge of the supply pump head to the key-slot of the supply pump gear, install the pump to the timing gear case.

  1. While holding the supply pump by hand, push the supply pump gear rearward to engage the pump gear and drive shaft.

  1. Temporarily install the supply pump with the 2 nuts.



    A077989
  1. Using SST, hold the crankshaft.

    SST
    09213-58013  
    09330-00021  

  1. Install the supply pump gear set nut.

    HINT:
    Set a new O-ring before tightening the supply pump gear set nut.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



    A076978
  1. Temporarily install the supply pump stay with the 2 bolts on the engine block side.

  1. Tighten the 2 nuts for the injection pump.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



    A070710
  1. Install the camshaft timing pulley flange No.2 and pump drive shaft pulley with the 4 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



3. CHECK PUMP DRIVE SHAFT THRUST CLEARANCE


    A071144
  1. Push the pump drive shaft pulley back and forth to check a thrust clearance of the injection pump drive shaft.

    Thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    NOTICE:
    Make sure that the crankshaft pulley's notch is at 30 degree in the counterclockwise direction form the TDC position.

    HINT:
    If there is not thrust clearance, disassemble and reassemble the injection pump and pump drive shaft pulley.



4. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
  1. Also, if the supply pump is replaced, the fuel inlet pipe must be replaced.
  2. Be careful not to adhere dusts, dirt or any other materials onto the joint area of the fuel inlet pipe.

  1. Temporarily install the fuel inlet pipe.

  1. Using SST, tighten the injection pipe on the common rail side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST

  1. Using SST, tighten the injection pipe on the supply pump side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST



5. INSTALL INJECTION PIPE
SST
09023-12701  

NOTICE:
  1. When replacing the injector replace the injection pipe as well.
  2. Keep clean the joint of the injection pipe.



  1. Install the injection pipes.



      A103532
    1. Temporarily install the 4 injection pipes.



    2. A103526
    3. Install the injection pipe clamp No.3 in 2 nuts.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    4. A103532E01
    5. Fasten the union sequentially, from the injection pipe common rail to the injector, using SST.

      SST
      09023-12701  

      Torque:
      Use union nut wrench and torque wrench:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }



6. INSTALL OIL LEVEL GAGE GUIDE
  1. Install a new O-ring to the oil level gauge guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the oil level gauge guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the oil level gauge.



7. CONNECT INTAKE AIR CONNECTOR (w/o EGR Valve)


    A106848E01
  1. Temporarily install 2 new gaskets and intake air connector No.2 to the intake air connector.



    A106846
  1. Temporarily tighten the intake air connector assembly with the bolt and 2 nuts.

  1. Tighten the manifold stay with the bolt.

  1. Tighten the intake air connector with the bolt and 2 nuts.

  1. Install the vacuum hose to the intake air connector.



8. TEMPORARILY TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)


  1. Temporarily tighten the EGR valve assembly with the sensor.



      A115761E01
    1. Install 2 new gaskets and the EGR valve to the intake air connector as shown in the illustration.



    2. A102287
    3. Temporarily tighten the intake air connector with EGR valve assembly to the intake manifold with the bolt and the 2 nuts.

    4. Install the vacuum hose to the intake air connector.

    5. Temporarily tighten the manifold stay with the bolt.



    6. A103043
    7. Connect the EGR valve position sensor connector.

    8. Connect the intake air temperature sensor connector.



  1. Install the vacuum regulating valve.



      A103046
    1. Install the vacuum regulating valve with the 2 bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Connect the 2 vacuum hoses and the regulating valve connector.



9. INSTALL EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)


    A106845
  1. Install the 2 gaskets to the cylinder head and EGR pipe sub-assembly as shown in the illustration.



    A106844
  1. Install the EGR pipe sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the intake air connector with the bolt and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the manifold stay.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



10. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)
  1. Remove the 3 bolts, the 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.



11. INSTALL DIESEL THROTTLE BODY ASSEMBLY

NOTICE:
After removing and installing, or replacing the throttle body, be sure to perform the operation check.

  1. Install a new gasket to intake air connector.



    A102902
  1. Install the throttle body with the 2 bolts and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A102282
  1. Connect the 2 throttle body connectors.



12. INSTALL AIR HOSE NO.4


    A102281
  1. Install the air hose No.4 with the 2 clamps.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



13. INSTALL EGR PIPE SUB-ASSEMBLY (w/ EGR Valve)


    A106845
  1. Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.



    A106844
  1. Install the EGR pipe with the 2 bolts and the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A106043
  1. Connect the fuel pressure sensor connector.



14. INSTALL OIL RETURN HOSE


    A106042
  1. Connect the oil return hose with the clip.



15. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY


    A102278
  1. Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



16. INSTALL TIMING BELT


    A070691E01
  1. Check that the timing marks are aligned as shown in the illustration.

  1. Install the timing belt to pump drive shaft pulley, camshaft timing pulley and timing belt idler No.1 in sequence.



    A070548
  1. Set the tensioner to the press upright.

    NOTICE:
    1. Do not allow the rod end to scratch and deform.
    2. Press the tensioner rod in upward.
    3. Protect a tip of the push rod with a rag in order to prevent damage.

  1. Using a press, slowly apply 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force to the push rod.

    NOTICE:
    Do not apply loads 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) or more on the push rod.

  1. Align the holes of push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Uniformly tighten the 2 bolts and install the tensioner

  1. Remove the 1.5 mm hexagon wrench from the tensioner.



    A070549E01
  1. Turn the crankshaft in the clockwise direction twice, check that the timing marks are aligned as shown in the illustration.



17. INSTALL TIMING BELT NO.1 COVER


    A102815
  1. Install the timing belt No.1 cover with the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the wire harness clamp.



18. INSTALL FAN AND GENERATOR V BELT


    A102808E03
  1. Install the drive belt by rotating the tensioner pulley in clockwise direction with the pulley set bolt of the tensioner.

    NOTICE:
    Make sure that the V belt is set properly at each pulley.



    A080039E01
  1. Make sure that the indicator mark of the tensioner is within range A.



19. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



20. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



21. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



22. INSTALL FRONT DOOR SCUFF PLATE RH


23. CONNECT BATTERY NEGATIVE CABLE


24. BLEED FUEL LINE


    A114068E01
  1. Using the hand pump, bleed air from the fuel system until pumping becomes difficult.



25. CHECK FOR FUEL LEAKAGE
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECD / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
      2. Above conditions preserved while test is ON