Home › ENGINE ยท 5L-E › COOLING › RADIATOR

RADIATOR > INSTALLATION

for Preparation Click here



1. INSTALL RADIATOR ASSEMBLY


    A102446
  1. Install the radiator assembly to the vehicle

    NOTICE:
    Do not drop the radiator assembly.



2. INSTALL FAN SHROUD NO.2


    A102971E04
  1. Install the fan shroud No.2 with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Do not drop the radiator assembly



3. INSTALL FAN SHROUD


    A116096
  1. Install the fan shroud with the 6 bolts.

    Torque:
    5.4 N*m{ 53 kgf*cm , 48 in.*lbf }

    NOTICE:
    Do not drop the radiator assembly.



4. INSTALL COOLING FAN ECU


    A116095
  1. Install the cooling fan ECU with the 2 bolts and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. INSTALL RADIATOR SUPPORT UPPER


    A103434E07
  1. Install the radiator support upper with the 6 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



6. INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
  1. Install the windshield washer motor and pump assembly with the 2 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }



7. INSTALL RADIATOR RESERVE TANK ASSEMBLY
  1. Install the radiator reserve tank assembly with the bolt

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL HOOD LOCK ASSEMBLY
  1. Install the hood lock cable assembly to the hood lock assembly.



    A102027E04
  1. Install the hood lock assembly with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. INSTALL W/RECEIVER CONDENSER ASSEMBLY


10. INSTALL COOLER REFRIGERANT LIQUID PIPE A


11. INSTALL COOLER REFRIGERANT DISCHARGE PIPE A


12. INSTALL FRONT BUMPER REINFORCEMENT


13. INSTALL FRONT FLOOR CROSS MEMBER REINFORCEMENT SUB-ASSEMBLY RH


14. INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY


15. INSTALL AIR INLET DUCT NO.1


    A116094
  1. Install the air inlet duct No.1 with the 6 clamps.



16. INSTALL FRONT BUMPER


17. INSTALL STEP PLATE COVER RH


18. INSTALL STEP PLATE COVER LH


19. INSTALL RADIATOR GRILLE


20. ADD ENGINE COOLANT
  1. Close the engine drain plug.

    Torque:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }

  1. Close the radiator drain cock plug.

  1. Slowly fill the cooling system with coolant.

    HINT:
    The coolant level inside the radiator should be abserved after pressing the radiator hose inlet and radiator hose outlet by hand..

  1. Slowly pour coolant into the radiator reserve tank until it reaches the FULL line.

  1. Install the radiator cap to the radiator reserve tank.

  1. Press the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add coolant to the FULL line of the radiator reservoir.



21. CHARGE REFRIGERANT


22. ENGINE START


23. ENGINE COOLANT LEVEL


24. CHECK FOR ENGINE COOLANT LEAKS