WATER PUMP > REMOVAL |
| 1. DISCONNECT BATTERY NEGATIVE CABLE |
| 2. REMOVE ENGINE UNDER COVER NO.1 |
| 3. REMOVE FRONT DOOR SCUFF PLATE RH |
| 4. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
| 5. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
| 6. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY |
Roll up the carpet, and remove the engine service hole sub cover assembly.
| 7. REMOVE FENDER APRON MUDGUARD SEAL RH |
| 8. REMOVE FAN AND GENERATOR V BELT |
![]() |
Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.
| 9. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning) |
Disconnect the connector.
![]() |
Remove the 4 bolts and compressor and magnetic clutch.
| 10. REMOVE AIR TUBE ASSEMBLY |
Remove the 2 clamps, 2 bolts and air tube assembly.
| 11. REMOVE AIR CLEANER HOSE ASSEMBLY |
Remove the bolt and air cleaner hose assembly.
| 12. REMOVE COMPRESSOR OUTLET ELBOW |
![]() |
Remove the 2 bolts and 2 clamps, then remove the compressor outlet elbow.
| 13. REMOVE IDLE PULLEY ASSEMBLY (w/ Air Conditioning) |
![]() |
Remove the bolt and washer, then remove the idle No.2 pulley assembly.
| 14. REMOVE GENERATOR BRACKET |
![]() |
Remove the 2 bolts, then remove the generator bracket.
| 15. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the generator connector.
Remove the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Remove the bolt and generator assembly.
| 16. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
Remove the 4 bolts and belt tensioner assembly.
| 17. REMOVE FAN PULLEY |
Remove the 4 nuts, 4 washer and fun pulley.
| 18. REMOVE TIMING BELT NO.1 COVER |
Remove the wire harness clamp.
![]() |
Remove the 6 bolts and timing belt cover No.1.
| 19. REMOVE TIMING BELT |
![]() |
Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.
![]() |
Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.
Remove the timing belt.
| 20. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY |
![]() |
Remove the 2 bolts and vane pump oil reservoir assembly.
| 21. DISCONNECT OIL RETURN HOSE (w/ Intercooler) |
| 22. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve) |
![]() |
Disconnect the fuel pressure sensor connector.
![]() |
Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.
Remove the 2 gaskets.
| 23. REMOVE AIR HOSE NO.4 |
![]() |
Loosen the 2 clamps.
Remove the air hose No.4.
| 24. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the 2 throttle body connectors.
![]() |
Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.
Remove the gasket from intake air connector.
| 25. REMOVE ENGINE SERVICE HOLE COVER NO.2 |
![]() |
Roll up the carpet.
Remove the 3 bolts and the engine service hole cover No.2.
| 26. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve) |
Remove the vacuum regulating valve.
![]() |
Remove the 2 vacuum hoses and the vacuum regulating valve connector.
Remove the 2 bolts and the vacuum regulating valve.
Remove the EGR valve assembly with the sensor.
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from the intake air connector.
![]() |
Disconnect the intake air temperature sensor connector.
Disconnect the EGR valve position sensor connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and EGR valve assembly from the intake air connector.
| 27. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve) |
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from intake air connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and intake air connector No.2 from the intake air connector.
| 28. REMOVE OIL LEVEL GAGE GUIDE |
Remove the oil level gauge.
Remove the bolt and oil level gauge guide.
| 29. REMOVE INJECTION PIPE |
Remove the injection pipe.
![]() |
Remove the 2 nuts and injection pipe clamp No.3.
![]() |
Using SST, remove the 4 injection pipes.
| 30. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
Using SST, remove the fuel inlet pipe sub-assembly.
| 31. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.
Disconnect the ventilation hose.
Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
| 32. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.
![]() |
Using SST, remove the camshaft timing pulley.
| 33. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1 |
![]() |
Using a 10 mm socket hexagonal wrench remove the timing belt idler No.1.
| 34. REMOVE TIMING BELT NO.2 COVER |
![]() |
Remove the 4 bolts and nuts, then remove the timing belt No.2 cover.
| 35. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 5 bolts, 2 nuts and water pump assembly.