Home › ENGINE ยท 2TR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL INJECTOR ASSEMBLY
  1. Apply a light coat of grease or gasoline to new O-rings and install them to the injector spacers.

    NOTICE:
    Make sure that the O-rings are installed between the parts correctly.

  1. Install the injection spacers.

  1. Apply a light coat of grease or gasoline to the place where the delivery pipe touches the O-ring.



    A087155
  1. To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it right and left.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    G036023
  1. Install the 4 spacers to the cylinder head.

  1. Install the delivery pipe spacers.



    A087154
  1. Temporarily install the 2 bolts and fuel delivery pipe together with the 4 injectors.

    NOTICE:
    1. Do not drop the fuel injector when installing the fuel delivery pipe.
    2. Make sure that the fuel injector turns smoothly.

  1. Fully tighten the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 10 ft.*lbf }

  1. Apply a light coat of grease or gasoline to the place where the delivery pipe touches the O-ring.

  1. Install the 2 bolts and pressure pulsation damper assembly.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 2 fuel hoses.



3. INSTALL FUEL HOSE
  1. Align the connector and pipe. Push on the connector until the retainer locks with a click sound. (Click here)

  1. Pull the connector to check that the connector is securely connected. (Click here)



    A087756E01
  1. Install the connector and lock it with the fuel hose connector cover. (Click here)



4. INSTALL THROTTLE BODY ASSEMBLY


    A102440E01
  1. Install a new gasket onto the intake manifold.

    HINT:
    Fit the gasket to the cutout of the intake manifold.



    A102438E02
  1. Install the throttle body assembly with the 2 bolts and 2 nuts. (A)

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the water by-pass hose. (B)

  1. Connect the water by-pass hose No.2. (C)

  1. Connect the throttle motor connector. (D)



5. INSTALL INTAKE AIR CONNECTOR
  1. Temporarily install the intake air connector to the throttle body assembly.



    A102437E02
  1. Connect the ventilation hose No.2 and the vacuum hose. (A)

  1. Install the intake air connector with the 2 bolts. (B)

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts. (C)

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Tighten the 2 hose clamp bolts. (D)



6. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



7. INSTALL FRONT DOOR SCUFF PLATE RH


8. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



9. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



10. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs and fill the reservoir tank with coolant to the top of the inlet.

  1. Remove the 2-way that is located near the throttle body.

  1. When air is bled and the coolant drains out, firmly install the 2-way.

  1. Add coolant up to the B line mark in the reservoir tank and install the radiator cap.

    Coolant capacity:

    Condition
    Capacity
    w/ rear heater
    15.0 liters (15.8 US qts, 13.2 lmp. qts)
    w/o rear heater
    13.0 liters (13.7 US qts, 11.4 lmp. qts)

  1. Warm up the engine.

  1. After the engine cools down, check that the coolant level is between the LOW and FULL level marks.



11. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold. If the engine coolant level is low, check for leaks and add "TOYOTA Super Long Life Coolant (SLLC)" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.



12. CONNECT BATTERY NEGATIVE CABLE


13. INSPECT FOR FUEL LEAKS
  1. When using the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the on position and intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.



  1. When not using the intelligent tester.



      A103380E01
    1. Disconnect the fuel pump connector.

    2. Using a service wire, connect terminals FP and +B of the relay block.

      NOTICE:
      Pay attention to the terminal connecting position to avoid a malfunction.

    3. Turn the ignition switch to the ON position, and check that the fuel pump operates.

      NOTICE:
      Do not start the engine.

  1. Check that there are no fuel leaks anywhere on the fuel system after doing maintenance.

  1. Check that the pulsation damper screw rises up when the fuel pump operates.
    If operation is not as specified, check the following parts:

    1. Fusible link
    2. Fuel pump
    3. Wiring connections
    4. ECM
    5. Fuses

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.