FUEL INJECTOR > REMOVAL |
| 1. CHECK INJECTION COMPENSATION CODE |
Check that the injection compensation code registered in the injector assembly installed on each cylinder match the ones registered in the engine ECU (Click here).
If they do not match, follow the procedures below to correct the registration details and recheck the symptom.
Correct the registration details by following the procedures in "resister injection compensation code" (Click here).
After correcting the registration details, check if the same symptom occurs as when the vehicle was brought in.
| 2. REMOVE BATTERY SERVICE HOLE COVER (w/ Sub-Battery) |
| 3. DISCONNECT BATTERY NEGATIVE CABLE |
| 4. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover) |
| 5. DRAIN ENGINE COOLANT |
Remove the radiator cap.
Loosen the radiator drain cock plug and a cylinder block drain cock plug. Then drain the coolant.

| 6. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
Perform the same procedure as above on the opposite side.
| 7. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
Perform the same procedure as above on the opposite side.
| 8. REMOVE FRONT DOOR SCUFF PLATE RH |
| 9. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY |
![]() |
Remove the 2 bolts and vane pump oil reservoir assembly.
| 10. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY |
Roll up the carpet, and remove the engine service hole sub cover assembly.
| 11. DISCONNECT OIL RETURN HOSE (w/ Inter cooler) |
![]() |
Loosen the clip.
Disconnect the oil return hose from the intake manifold.
| 12. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve) |
![]() |
Disconnect the fuel pressure sensor connector.
![]() |
Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.
Remove the 2 gaskets.
| 13. REMOVE AIR HOSE NO.4 |
![]() |
Loosen the 2 clamps.
Remove the air hose No.4.
| 14. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the 2 throttle body connectors.
![]() |
Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.
Remove the gasket from intake air connector.
| 15. REMOVE ENGINE SERVICE HOLE COVER NO.2 |
![]() |
Roll up the carpet.
Remove the 3 bolts and the engine service hole cover No.2.
| 16. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve) |
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from intake air connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and intake air connector No.2 from the intake air connector.
| 17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Remove the vacuum regulating valve.
![]() |
Remove the 2 vacuum hoses and the vacuum regulating valve connector.
Remove the 2 bolts and the vacuum regulating valve.
Remove the EGR valve assembly with the sensor.
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from the intake air connector.
![]() |
Disconnect the intake air temperature sensor connector.
Disconnect the EGR valve position sensor connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and EGR valve assembly from the intake air connector.
| 18. REMOVE OIL LEVEL GAGE GUIDE |
Remove the oil level gauge.
Remove the bolt and oil level gauge guide.
| 19. REMOVE INJECTION PIPE |
Remove the injection pipe.
![]() |
Remove the 2 nuts and injection pipe clamp No.3.
![]() |
Using SST, remove the 4 injection pipes.
| 20. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY NO.2 |
![]() |
Disconnect 3 fuel hoses from nozzle leakage pipe assembly No.2.
![]() |
Remove the union bolt from nozzle leakage pipe No.2.
![]() |
Remove the 2 bolts and nozzle leakage pipe No.2.
Remove the gasket from nozzle leakage pipe No.2.
| 21. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.
Disconnect the ventilation hose.
Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
| 22. REMOVE INJECTOR ASSEMBLY |
Remove the nozzle leakage pipe assembly.
![]() |
Remove the union bolt, 4 hollow screws, 5 gaskets and nozzle leakage pipe assembly.
Remove the nozzle holder clamp.
![]() |
Remove the 4 bolts, washers and 4 nozzle holder clamps.
Remove the injector assemblies.