AUTOMATIC TRANSMISSION UNIT > INSPECTION |
| 1. INSPECT EXTENSION HOUSING SUB-ASSEMBLY |
![]() |
Using a cylinder gauge, measure the inside diameter of the extension housing bushing.
| 2. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY |
![]() |
Remove the oil cleaner magnets, and use them to collect steel particles.
Carefully lock at the foreign matter and particles in the pan and on the oil cleaner magnets to anticipate the type of wear you will find in the transmission.
| 3. INSPECT FRONT PLANETARY GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the planetary ring gear bushing.
| 4. INSPECT PLANETARY PINION GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the planetary pinion gear thrust clearance.
| 5. INSPECT PACK CLEARANCE OF SECOND BRAKE |
![]() |
Using a feeler gauge, measure the clearance between the snap ring and the flange.
| 6. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISK |
![]() |
Check if the sliding surfaces of the disc, the plate and the flange are worn or burnt. If necessary, replace them.
| 7. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE |
![]() |
Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.
| 8. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Check the return spring free length together with the spring seat.
| 9. INSPECT AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY |
![]() |
Using a cylinder gauge, measure the inside diameter of the transmission case rear bushing.
| 10. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE |
![]() |
Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.
| 11. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE |
![]() |
Using a feeler gauge, measure the clearance between the plate and the 2nd brake drum.
| No. | Thickness | No. | Thickness |
| 67 | 5.4 mm (0.213 in.) | 52 | 4.6 mm (0.181 in.) |
| 66 | 5.2 mm (0.205 in.) | 53 | 4.4 mm (0.173 in.) |
| 50 | 5.0 mm (0.197 in.) | 54 | 4.2 mm (0.165 in.) |
| 51 | 4.8 mm (0.189 in.) | 55 | 4.0 mm (0.157 in.) |
| 12. INSPECT PISTON STROKE OF 2ND COAST BRAKE |
![]() |
Place a mark on the 2nd coast brake piston rod.
Using SST, measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| 13. INSPECT OUTPUT SHAFT |
![]() |
Using a dial indicator, measure the end play of the output shaft with hand.
Check that the output shaft rotates smoothly.
| 14. INSPECT OVERDRIVE BRAKE PISTON |
![]() |
Place SST and a dial indicator onto the O/D brake piston.
![]() |
Measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| No. | Thickness | No. | Thickness |
| 77 | 3.3 mm (0.130 in.) | 81 | 3.8 mm (0.150 in.) |
| 78 | 3.5 mm (0.138 in.) | 82 | 3.9 mm (0.154 in.) |
| 79 | 3.6 mm (0.142 in.) | 83 | 4.0 mm (0.157 in.) |
| 80 | 3.7 mm (0.146 in.) | - | - |
| 15. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION |
![]() |
Check for the sound while while applying compressed air into the oil hole indicated in the illustration.
O/D direct clutch
Direct clutch
Forward clutch
O/D brake
2nd coast brake
2nd brake
1st and reverse brake
| 16. INSPECT INPUT SHAFT SUB-ASSEMBLY |
![]() |
Make sure the input shaft rotates smoothly.