Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION



D029783E01


Standard:

Mark
Front Race Diameter Inside / Outside mm (in.)
Thrust Bearing Diameter Inside / Outside mm (in.)
Rear Race Diameter Inside / Outside mm (in.)
A
28.45 (1.120) / 47.3 (1.862)
29.2 (1.15) / 50.2 (1.976)
-
B
28.6 (1.126) / 46.4 (1.827)
28.9 (1.138) / 50.2 (1.976)
-
C
24.7 (0.972) / 41.8 (1.646)
24.2 (0.953) / 47.8 (1.882)
-
D
37.2 (1.465) / 58.8 (2.315)
33.8 (1.331) / 50.0 (1.969)
-
E
36.8 (1.449) / 50.9 (2.004)
33.7 (1.327) / 47.6 (1.874)
-
F
-
26.0 (1.024) / 42.8 (1.685)
26.8 (1.055) / 53.67 (2.113)
G
-
49.9 (1.965) / 64.4 (2.535)
53.4 (2.102) / 63.6 (2.504)
H
33.7 (1.327) / 47.6 (1.874)
35.5 (1.398) / 47.7 (1.878)
-
I
28.5 (1.122) / 44.2 (1.740)
27.7 (1.091) / 44.2 (1.740)
-
J
-
39.38 (1.550) / 58.1 (2.287)
-



2. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


    AT05393
  1. Install the transmission case in the overhaul attachment.



3. INSTALL 1ST AND REVERSE BRAKE PISTON NO.1


    AT08209E06
  1. Coat 3 new O-rings with ATF.

  1. Install the 2 O-rings on the 1st and reverse brake piston No.1.

  1. Install the O-rings on the reaction sleeve.

  1. Install the 1st and reverse brake piston No.1 to the reaction sleeve.



4. INSTALL BRAKE REACTION SLEEVE


    D001243
  1. Coat a new O-ring with ATF, and install it to the reaction sleeve.

  1. With the brake piston No.1 underneath (the rear side), install the brake reaction sleeve and the brake piston No.1 to the transmission case.

    NOTICE:
    Be careful not to damage the O-rings.



5. INSTALL 1ST & REVERSE BRAKE PISTON NO.2


    AT08333E05
  1. Coat new O-ring with ATF.

  1. Install the O-ring on brake piston No.2.

  1. With the spring seat of the piston upwards (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.



6. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    AT05429
  1. Place the piston return spring onto the 1st and reverse brake piston.



    AT08303E02
  1. Set SST as shown, and compress the return spring with SST.

    SST
    09350-30020   (09350-07050, 09350-07070)

    NOTICE:
    Stop compressing when the spring sheet is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from being deformed.

  1. Using a screwdriver, install the snap ring. Make sure the end gap of the snap ring is not aligned with the spring retainer claw.



7. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE


    AT05890
  1. Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.



8. INSTALL REAR PLANETARY FLANGE THRUST NEEDLE ROLLER BEARING


    Z005138E02
  1. Coat the assembled bearing and race with petroleum jelly.

  1. Install it onto the case.

    Bearing diameter:

    Inside
    Outside
    Bearing
    39.38 mm (1.550 in.)
    58.1 mm (2.287 in.)



9. INSTALL REAR PLANETARY GEAR ASSEMBLY


    AT05107
  1. Install the leaf spring.



    AT08208
  1. Install the flange with the rounded edge facing upward.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P - D - P



    AT07893
  1. Align the teeth on the flange, the discs and the plates.



    Q004066
  1. Face the snap ring upward (front side), and install the 2nd brake drum to the planetary gear.

    NOTICE:
    Face the oil hole in the drum towards the lower side of the transmission case (the side where the valve body is installed).



    Q004068E02
  1. Align the splines of the transmission case with the assembled rear planetary gear and the 1st and reverse brake with the output shaft, indicated by A.



    AT05158
  1. Install the assembled output shaft.



    Z005131E02
  1. Rest the output shaft on wooden blocks.



    AT05396E02
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)



10. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE


    AT08224
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bushing.

    Maximum inside diameter:
    38.19 mm (1.5035 in.)

    If the inside diameter is greater than the maximum, replace the transmission case.



11. INSTALL 2ND BRAKE PISTON SLEEVE


12. INSTALL BRAKE DRUM GASKET


    AT04469
  1. Coat a new gasket with ATF.

  1. Install the brake drum gasket.



13. INSTALL 1 WAY CLUTCH ASSEMBLY


    AT05231
  1. Install the thrust washer onto the 2nd brake.



    Z005133E02
  1. Install the 1 way clutch.



14. INSTALL 2ND BRAKE PACK


    AT05398E03
  1. Install the 1.8 mm (0.071 in.) thick plate with the rounded edge side of the plate facing the disc.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P

  1. Install the flange with the rounded edge of the flange facing the disc.



    AT05476
  1. Using a screwdriver, install the snap ring.



15. INSPECT PACK CLEARANCE OF SECOND BRAKE


    AT05215
  1. Using a feeler gauge, measure the clearance between the snap ring and the flange.

    Clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is outside the standard, check for an improper installation.



16. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


    Q000840
  1. While turning the planetary sun gear clockwise, install it into the No.1 one-way clutch.

    HINT:
    Confirm the thrust washer is installed correctly.



17. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    D029745E02
  1. Coat the bearing and race with petroleum jelly and install them onto the front planetary gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    35.5 mm (1.398 in.)
    47.7 mm (1.878 in.)
    Race
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)



    D029741
  1. Install the front planetary gear to the sun gear input drum.



    D029740E02
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the wooden blocks or equivalent under the output shaft. case.



    D029744
  1. Coat the race with petroleum jelly, and install it onto the front planetary gear.

    Race diameter:

    Inside
    Outside
    Race
    53.4 mm (2.102 in.)
    63.6 mm (2.504 in.)



18. INSTALL 2ND COST BRAKE BAND ASSEMBLY


    Q004030
  1. Install the 2nd coast brake band to the case.



    Q000788
  1. Install the E-ring to the pin.

  1. Install the pin through the brake band.

  1. Install the E-ring to the pin.



19. INSTALL DIRECT CLUTCH ASSEMBLY


    D006214E04
  1. Install the bearing and the thrust washer to the forward clutch.



    AT05262E02
  1. Install the direct clutch to the forward clutch.



20. INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY


    Z005137E02
  1. Coat the bearing and the race with petroleum jelly, and install them onto the forward clutch.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    42.8 mm (1.685 in.)
    Race
    26.0 mm (1.024 in.)
    42.8 mm (1.685 in.)



    Z005136E02
  1. Coat the race with petroleum jelly, and install it onto the front planetary ring gear.

    Race diameter:

    Inside
    Outside
    Race
    26.8 mm (1.055 in.)
    53.67 mm (2.113 in.)



    AT05432
  1. Align the flukes of the discs in the forward clutch.



    Q000838E02
  1. Align the splines of the front planetary ring gear with the flukes of the discs and install the front planetary ring gear to the forward clutch.



21. INSTALL FORWARD CLUTCH ASSEMBLY


    AT08306E02
  1. Coat the bearing and the race with petroleum jelly, and install them onto the ring gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    32.6 mm (1.283 in.)
    47.7 mm (1.878 in.)
    Race
    30.6 mm (1.205 in.)
    53.6 mm (2.110 in.)



    AT08234
  1. Install the assembled direct clutch, the forward clutch and the front planetary ring gear into the transmission case.



    AT05213
  1. Using vernier calipers, measure the distance between the sun gear input drum and the direct clutch drum as shown in the illustration.

    Distance:
    5.3 to 7.3 mm (0.209 to 0.287 in.)

    If the distance is outside the standard, check for an improper installation.



    Z005236E02
  1. Coat the bearing with petroleum jelly and install it onto the forward clutch.

    Bearing:

    Inside
    Outside
    Bearing
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)



22. INSTALL 2ND COAST BRAKE PISTON


    AT05086
  1. Coat 2 new O-rings with ATF, and install them to the cover.

  1. Install the spring, the piston assembly and the cover to the case.



    AT05127E02
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)



23. INSTALL PISTON STROKE OF 2ND COST BRAKE


24. INSTALL OVERDRIVE SUPPORT SUB-ASSEMBLY


    AT05110E03
  1. Coat the bearing and the race with petroleum jelly, and install it onto the O/D support assembly.

    Bearing and race diameter:

    Inside
    Outside
    Race
    36.8 mm (1.449 in.)
    50.9 mm (2.004 in.)
    Bearing
    33.8 mm (1.331 in.)
    50.0 mm (1.969 in.)



    AT05159
  1. Confirm the thrust washer is installed correctly.

    HINT:
    Make sure that the lug shape fits into the hole on the O/D support assembly.



    AT05400E02
  1. Using 2 bolts of SST, aim the bolt and the oil holes of the O/D support toward the valve body side, and align them with the bolt holes of the transmission case, and insert.

    SST
    09350-30020   (09350-07020)

  1. Temporarily tighten the 2 bolts.



    Q000618E02
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)

    HINT:
    Install the snap ring open end toward the valve body.



    AT05218
  1. Torque the 2 bolts.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }



25. INSPECT OUTPUT SHAFT


    Z006796
  1. Using a dial indicator, measure the end play of the output shaft with hand.

    End play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the values are outside the standard, check for an improper installation.

  1. Check that the output shaft rotates smoothly.



26. INSTALL OVERDRIVE BRAKE PACK


    AT05763
  1. Install the 4.0mm(0.157 in.) thick flange (flat ring) with the rounded edge side of the flange facing the discs.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    P - D - P - D - P - D

  1. Install the flange (stepped ring) with the flat side of the flange facing the disc.



    AT05233
  1. Using a screwdriver, install the snap ring.



27. INSPECT OVERDRIVE BRAKE PISTON


    AT05282E02
  1. Place SST and a dial indicator onto the O/D brake piston.

    SST
    09350-30020   (09350-06120)



    AT05147
  1. Measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Piston stroke:
    1.75 to 2.05 mm (0.0689 to 0.0807 in.)

    If the piston stroke is less than the limit, parts may have been assembled incorrectly, so check and reassemble again.
    If the piston stroke is still outside the standard, select another flange.

    HINT:
    There are 7 different thicknesses for the flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)
    -
    -



28. INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY


    Q000842
  1. Coat the race with petroleum jelly, and install it onto the O/D support.

    Race diameter:

    Inside
    Outside
    Race
    37.2 mm (1.465 in.)
    58.8 mm (2.315 in.)



    AT05146
  1. Install the O/D planetary ring gear.



    AT05126
  1. Coat the bearing and race with petroleum jelly, and install them onto the planetary ring gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    46.8 mm (1.843 in.)
    Race
    24.2 mm (0.953 in.)
    47.8 mm (1.882 in.)



    Z005128
  1. Coat the race with petroleum jelly, and install it onto the planetary gear.

    Race diameter:

    Inside
    Outside
    Race
    24.7 mm (0.972 in.)
    41.8 mm (1.646 in.)



    Q000619
  1. Install the O/D planetary gear, O/D direct clutch and 1 way clutch.



    AT04470E02
  1. Place SST on the transmission case.

    SST
    09350-36010   (09350-06090)

  1. Using vernier calipers, measure the distance between the tops of SST and the clutch drum.

    Standard distance:
    15.5 to 16.5 mm (0.610 to 0.650 in.)

    If the distance is outside the standard, check for an improper installation.



    AT08313E02
  1. Coat the bearing with petroleum jelly and install it onto the O/D direct clutch.

    Bearing diameter:

    Inside
    Outside
    Bearing
    29.2 mm (1.150 in.)
    50.2 mm (1.976 in.)



29. INSTALL OIL PUMP ASSEMBLY


    Z005237E02
  1. Coat the race with petroleum jelly, and install it onto the oil pump.

    Race diameter:

    Inside
    Outside
    Race
    28.45 mm (1.120 in.)
    47.3 mm (1.862 in.)

  1. Coat a new O-ring with ATF, and install it around the pump body.

  1. Place the oil pump through the input shaft, and align the bolt holes of the pump body with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the O/D direct clutch drum.

    NOTICE:
    Do not push on the oil pump strongly, or the oil seal ring will stick to the direct clutch drum.



    AT05404
  1. Install the 7 bolts.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }



30. INSPECT INPUT SHAFT SUB-ASSEMBLY


    AT05244E02
  1. Make sure the input shaft rotates smoothly.



31. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION


    AT05275E02
  1. Check for the sound while while applying compressed air into the oil hole indicated in the illustration.

    HINT:
    When inspecting the O/D direct clutch, check with the C0 accumulator piston hole is closed.

    If there is no noise, disassemble and check the installation condition of the parts.

    1. O/D direct clutch

    2. Direct clutch

    3. Forward clutch

    4. O/D brake

    5. 2nd coast brake

    6. 2nd brake

    7. 1st and reverse brake



32. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    AT05238E02
  1. Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals.

    SST
    09350-30020   (09350-07110)

  1. Coat the oil seal lip with MP grease.



33. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY


    D031556E03
  1. Install a new spacer to the manual valve lever.

  1. Install the manual valve lever shaft to the transmission case through the manual valve lever.



    AT05405
  1. Using a hammer, drive in a new pin.



    D006523
  1. Align the manual valve lever indentation with the spacer hole, and stake them with a punch.

  1. Make sure that the shaft rotates smoothly.



34. INSTALL PARKING LOCK PAWL SHAFT


    Q000776E02
  1. Install the E-ring to the shaft.

  1. Install the parking lock pawl, the shaft and the spring.



35. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    Z006797
  1. Connect the parking lock rod to the manual valve lever.



36. INSTALL PARKING LOCK PAWL BRACKET


    AT05406
  1. Install the parking lock pawl bracket with the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



    Z005222E02
  1. Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the pawl.



37. INSTALL C-0 ACCUMULATOR PISTON


    AT05010E02
  1. Coat new O-ring with ATF, and install them to the piston.



    D028075
  1. Install the 2 springs and accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    C-0 Inner
    46.0 mm (1.811 in.)
    14.02 mm (0.552 in.)
    Yellow
    C-0 Outer
    74.6 mm (2.137 in.)
    20.9 mm (0.823 in.)
    Orange



38. INSTALL B-0 ACCUMULATOR PISTON


    AT05010E02
  1. Coat new O-rings with ATF, and install them to the piston.



    D028074
  1. Install the spring and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    B-0
    63.6 mm (2.504 in.)
    16.0 mm (0.630 in.)
    Red



39. INSTALL C-2 ACCUMULATOR PISTON


    AT05010E02
  1. Coat new O-rings with ATF, and install them to the piston.



    D028073
  1. Install the 2 springs and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    C-2 Inner
    42.1 mm (1.657 in.)
    14.7 mm (0.579 in.)
    Pink
    C-2 Outer
    64.0 mm (2.519 in.)
    19.7 mm (0.776 in.)
    Blue



40. INSTALL B-2 ACCUMULATOR PISTON


    AT05010E02
  1. Coat new O-rings with ATF, and install them to the piston.



    D028072
  1. Install the spring and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    B-2
    70.5 mm (2.776 in.)
    19.7 mm (0.776 in.)
    Light Gray



41. INSTALL CHECK BALL BODY


    AT05098E02
  1. Install the check ball body and spring.



42. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    AT08393E02
  1. Align the groove of the manual valve with the pin of the lever.



    D029011E05
  1. Install the 20 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    23 mm (0.91 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    36 mm (1.42 in.)



43. INSTALL TRANSMISSION WIRE


    Q000625
  1. Coat a new O-ring with ATF, and install it to the solenoid wiring.

  1. Install the solenoid wiring to the case, and install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C058460
  1. Connect the connectors to each shift solenoid valve.



44. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    D005554
  1. Install 5 new gaskets on the oil strainer.



    D005550E02
  1. Install the oil strainer with the 4 bolts.

    Torque:
    110 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    14 mm (0.55 in.)
    Bolt B:
    20 mm (0.79 in.)
    Bolt C:
    23 mm (0.91 in.)



45. INSTALL TRANSMISSION OIL CLEANER MAGNET


    D029014E02
  1. Install the 3 magnets on the oil pan.



46. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    AT01362E06
  1. Remove any FIPG material, and be careful not to drop oil on the contacting surfaces of the transmission case and the oil pan.

  1. Apply FIPG to the oil pan.

    FIPG:
    Part No.08826-00090, THREE BOND 1281 or equivalent

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



47. INSTALL SENSOR ROTOR


    C114748E03
  1. Using a snap ring expander, install the front side snap ring.

  1. Install the key and sensor rotor.

  1. Using a snap ring expander, install the rear side snap ring.



48. INSTALL EXTENSION HOUSING DUST DEFLECTOR


    D005578
  1. Using a screwdriver and hammer, install a new extension housing dust deflector.



49. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


    C106499E01
  1. Using SST and a hammer, install a new extension housing oil seal.

    SST
    09950-60020   (09951-00580)
    09950-70010   (09951-07100)

    Oil seal in depth:
    6.0 +- 0.2 mm (0.236 +- 0.008 in.)



50. INSTALL EXTENSION HOUSING BUSH APPLY TUBE


    C114745E08
  1. Install the extension housing bush apply tube.



51. INSTALL EXTENSION HOUSING BUSH APPLY TUBE GASKET


    C114745E09
  1. Install the extension housing bush apply tube gasket.



52. INSTALL EXTENSION HOUSING SUB-ASSEMBLY


    C114744
  1. Apply seal packing or equivalent to the 6 bolts.

    Seal packing:
    Part No.08833-00080, THREE BOND 1344 LOCTITE 242 or equivalent

  1. Install the extension housing and a new gasket to the case with the 6 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }

    HINT:
    The 2 lower bolts are shorter.



53. INSTALL AUTOMATIC TRANSMISSION HOUSING


    C114749
  1. Clean the threads of the bolts and the case with white gasoline.

  1. Apply seal packing or equivalent to the 6 bolts.

    Seal packing:
    Part No.08833-00080, THREE BOND 1344 LOCTITE 242 or equivalent

  1. Install the transmission housing with the 6 bolts.

    Torque:
    14 mm bolt:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    17 mm bolt:
    57 N*m{ 580 kgf*cm , 42 ft.*lbf }



54. INSTALL TRANSMISSION REVOLUTION SENSOR


    C114743
  1. Coat a new O-ring with ATF, and install it to the sensor.

  1. Install the revolution sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



55. INSTALL SPEED SENSOR


    Q003894
  1. Coat a new O-ring with ATF, and install it to the sensor.

  1. Install the speed sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



56. INSTALL OIL COOLER TUBE UNION


    Q003892
  1. Coat new O-rings with ATF, and install them to each oil cooler tube union.

  1. Install the 2 oil cooler tube unions.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



57. INSTALL TEMPERATURE NO.2 SENSOR


    Q003891
  1. Coat a new O-ring with ATF, and install it to the temperature No.2 sensor.

  1. Install the temperature No.2 sensor.

    Torque:
    24 N*m{ 250 kgf*cm , 18 ft.*lbf }



58. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C101516E03
  1. Install the park/neutral position switch onto the manual valve lever shaft, and temporarily tighten the adjusting bolt.

  1. Install a new lock washer, and then install the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Using the control shaft lever, fully turn the manual lever shaft back, and then return 2 notches. It is now in neutral.



    D006517E01
  1. Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.



59. INSTALL TRANSMISSION CASE PLUG ASSEMBLY


    D005553
  1. Coat a new O-ring with ATF, and install it to the plug.

  1. Install the cable to the case with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 ft.*lbf }



60. INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE


61. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH
  1. Install the transmission control shaft lever LH with the bolt.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



62. INSTALL DRAIN (ATM) PLUG SUB-ASSEMBLY

Torque:
20 N*m{ 205 kgf*cm , 15 ft.*lbf }