Home › ENGINE ยท 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > TERMINALS OF ECM

for Preparation Click here



A066714E09

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BATT (B7-2) - E1 (D3-7)
B-R - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
IGSW (B9-9) - E1 (D3-7)
B-R - BR
Ignition switch
Ignition switch ON
9 to 14 V
+B (B9-1)- E1 (D3-7)
B-R - BR
Power source of ECM
Ignition switch ON
9 to 14 V
MREL (B9-8)- E1 (D3-7)
G-Y - BR
MAIN relay
Ignition switch ON
9 to 14 V
MREL (B9-8)- E1 (D3-7)
G-Y - BR
MAIN relay
10 seconds elapsed after ignition switch OFF
0 to 1.5 V
VC (D1-18) - E2 (D1-28)
L-B - Y-R
Power source of sensor (a specific voltage)
Ignition switch ON
4.5 to 5.5 V
VPA (B9-22) - EPA (B9-28)
L - W-L
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully released
0.6 to 1.0 V
VPA (B9-22) - EPA (B9-28)
L - W-L
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully depressed
3.0 to 4.6 V
VPA2 (B9-23) - EPA2 (B9-29)
B - W-R
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
1.4 to 1.8 V
VPA2 (B9-23) - EPA2 (B9-29)
B - W-R
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
3.7 to 5.0 V
VCPA (B9-26) - EPA (B9-28)
W - W-L
Power source of accelerator pedal position sensor (for VPA1)
Ignition switch ON
4.5 to 5.5 V
VCP2 (B9-27) - EPA2 (B9-29)
R-L - W-R
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
THA (D1-31) - E2 (D1-28)
R - Y-R
IAT sensor
Idling, intake air temperature at 20°C (68°F)
0.5 to 3.4 V
THW (D1-19) - E2 (D1-28)
R-W - Y-R
ECT sensor
Idling, engine coolant temperature at 80°C (176°F)
0.2 to 1.0 V
STA (B9-7) - E1 (D3-7)
R - BR
Starter signal
Cranking
6.0 V or more
#1 (D1-24) - E1 (D3-7)
#2 (D1-23) - E1 (D3-7)
#3 (D1-22) - E1 (D3-7)
#4 (D1-21) - E1 (D3-7)
G-R - BR
G-Y - BR
Y-B - BR
B-Y - BR
Injector
Idling
Pulse generation
(see waveform 2)
G1 (D3-23) - G- (D3-31)
R - G
Camshaft position sensor
Idling
Pulse generation
(see waveform 4)
NE+ (D1-27) - NE- (D1-34)
Y - L
Crankshaft position sensor
Idling
Pulse generation
(see waveform 4)
STP (B7-15) - E1 (D3-7)
R-W - BR
Stop lamp switch
Ignition switch ON, brake pedal depressed
7.5 to 14 V
STP (B7-15) - E1 (D3-7)
R-W - BR
Stop lamp switch
Ignition switch ON, brake pedal released
0 to 1.5 V
ST1- (B7-14) - E1 (D3-7)
R-L - BR
Stop lamp switch (opposite to STP)
Ignition switch ON, brake pedal depressed
0 to 1.5 V
ST1- (B7-14) - E1 (D3-7)
R-L - BR
Stop lamp switch (opposite to STP)
Ignition switch ON, brake pedal released
7.5 to 14 V
TC (B9-11) - E1 (D3-7)
P - BR
Terminal TC of DLC3
Ignition switch ON
9 to 14 V
W (B9-12) - E1 (D3-7)
G-R - BR
MIL
MIL illuminated
0 to 3 V
W (B9-12) - E1 (D3-7)
G-R - BR
MIL
MIL not illuminated
9 to 14 V
SPD (B7-17) - E1 (D3-7)
P-L - BR
Speed signal from combination meter
Ignition switch ON, driving wheel is rotating slowly
Pulse generation
(see waveform 7)
SIL (B9-18) - E1 (D3-7)
W - BR
Terminal SIL of DLC3
Connect intelligent tester to the DLC3
Pulse generation
PIM (D3-28) - E2 (D1-28)
P - Y-R
Manifold absolute pressure sensor
Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
1.3 to 1.9 V
PIM (D3-28) - E2 (D1-28)
P - Y-R
Manifold absolute pressure sensor
Same as atmospheric pressure
2.4 to 3.1 V
PIM (D3-28) - E2 (D1-28)
P - Y-R
Manifold absolute pressure sensor
Apply positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg)
3.7 to 4.3 V
IREL (B9-10) - E1 (D3-7)
R-L - BR
EDU relay
Ignition switch OFF
9 to 14 V
IREL (B9-10) - E1 (D3-7)
R-L - BR
EDU relay
Idling
0 to 1.5 V
TACH (B9-4) - E1 (D3-7)
B-Y - BR
Engine speed
Idling
Pulse generation
PCR1 (D1-26) - E2 (D1-28)
P - Y-R
Common rail pressure sensor (main)
Idling
1.3 to 1.8 V
GREL (B9-15) - E1 (D3-7)
G - BR
Glow plug relay
Cranking
9 to 14 V
GREL (B9-15) - E1 (D3-7)
G - BR
Glow plug relay
Idling
0 to 1.5 V
THF (D1-29) - E2 (D1-28)
R-L - Y-R
Fuel temperature sensor
Ignition switch ON
0.5 to 3.4 V
ALT (D1-8) - E1 (D3-7)
W - BR
Generator (Alternator) duty ratio
Idling
Pulse generation
PCV+ (D1-2) - PCV- (D1-1)
P - Y-R
Suction control valve
Idling
Pulse generation
(see waveform 1)
INJF (D1-25) - E1 (D3-7)
Y-R - BR
EDU
Idling
Pulse generation
(see waveform 3)
VLU (D3-29) - E2 (D1-28)
R-L - Y-R
Throttle position sensor
Ignition switch ON, throttle valve fully opened
2.8 to 4.2 V
VLU (D3-29) - E2 (D1-28)
R-L - BR
Throttle position sensor
Ignition switch ON, throttle valve fully closed
0.3 to 0.9 V
LUSL (D3-4) - E1 (D3-7)
B - BR
Throttle valve duty signal
Engine warmed up, racing engine
Pulse generation
(see waveform 6)
EGR (D3-9) - E1 (D3-7)
B-W - BR
E-VRV for EGR
Ignition switch ON
Pulse generation
(see waveform 5)
EGLS (D3-33) - E2 (D1-28)
P - Y-R
EGR valve position sensor
Ignition switch ON
0.3 to 1.3 V
CAN+ (B7-22)* - E1 (D3-1)
L - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 8)
CAN- (B7-21)* - E1 (D3-1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 9)
CANH (B7-24) - E1 (B7-1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 8)
CANL (B7-23) - E1 (B7-1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 9)

HINT:
*: Only for A/T


Waveform 1


    A097624E02
  1. Suction control valve signal
    Symbols (Terminal No.)
    PCV+ (D1-2) - PCV- (D1-1)
    Tool Setting
    10 V/DIV., 5 msec./DIV.
    Condition
    Idling or cranking with warm engine

    HINT:
    The waveform varies depending on the suction control valve operation.


Waveform 2


    A009438E02
  1. Injector No. 1 injection signal

  2. Injector No. 2 injection signal

  3. Injector No. 3 injection signal

  4. Injector No. 4 injection signal
    Symbols (Terminal No.)
    (a) #1 (D1-24) - E1 (D3-7)
    (b) #3 (D1-22) - E1 (D3-7)
    (c) #4 (D1-21) - E1 (D3-7)
    (d) #2 (D1-23) - E1 (D3-7)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the injector injection.


Waveform 3


    A009437E02
  1. Injector injection confirmation signal
    Symbols (Terminal No.)
    INJF (D1-25) - E1 (D3-7)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the injector injection.


Waveform 4


    A098437E02
  1. Crankshaft position sensor signal

  2. Camshaft position sensor signal
    Symbol (Terminal No.)
    (a) NE+ (D1-27) - NE- (D1-34)
    (b) G1 (D3-23) - G- (E-31)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the engine revolution.


Waveform 5


    A096634E02
  1. E-VRV for EGR signal
    Symbols (Terminal No.)
    EGR (D3-9) - E1 (D3-7)
    Tool Setting
    2 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform changes depending on the electric vacuum regulating valve for EGR operation.


Waveform 6


    A091225E02
  1. Diesel throttle signal
    Symbols (Terminal No.)
    LUSL (D3-4) - E1 (D3-7)
    Tool Setting
    1 V/DIV., 2 msec./DIV.
    Condition
    Warm engine with racing engine

    HINT:
    The waveform varies depending on the throttle valve operation.


Waveform 7


    G037487E03
  1. Vehicle speed signal
    Symbols (Terminal No.)
    SPD (B7-17) - E1 (D3-7)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    While driving the vehicle

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.


Waveform 8


    G036660E02
  1. CAN communication signal
    Symbols (Terminal No.)
    CANH (D3-24), CAN+ (B7-22) - E1 (D3-7)
    Tool Setting
    1 V/DIV., 10 msec./DIV.
    Condition
    Engine is stopped, ignition ON

    HINT:
    The wavelength becomes shorter as the CAN communication signal


Waveform 9


    G036661E02
  1. CAN communication signal
    Symbols (Terminal No.)
    CANL (D3-23), CAN- (B7-21) - E1 (D3-7)
    Tool Setting
    1 V/DIV., 10 msec./DIV.
    Condition
    Engine is stopped, ignition ON

    HINT:
    The waveform varies depending on the CAN communication signal.