Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0115/22    Engine Coolant Temperature Circuit

DTC    P0117/22    Engine Coolant Temperature Circuit Low Input

DTC    P0118/22    Engine Coolant Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

A thermistor is built in the Engine Coolant Temperature (ECT) sensor and changes the resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the inlet air temperature sensor.

HINT:
If the ECM detects the DTC P0115/22, P0117/22 or P0118/22, it operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).


DTC No.
DTC Detection Condition
Trouble Area
P0115/22
Open or short in ECT sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0117/22
Short in ECT sensor circuit for 0.5 seconds
(sensor resistance value less than 79 Ω)
(1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0118/22
Open in ECT sensor circuit for 0.5 seconds
(sensor resistance value more than 156 kΩ)
(1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM

HINT:
When DTC P0115/22, P0117/22 and/or P0118/22 is detected, check the engine coolant temperature by entering the following menus on the intelligent tester : Powertrain / ECD / Data List / Coolant Temp.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit


WIRING DIAGRAM


A110950E02


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:

1.READ VALUE OF ENGINE COOLANT TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Coolant Temp.

  1. Read the values.

    OK:
    75 to 95°C (167 to 203°F) after warming up the engine.


    Result:

    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (Same as actual engine coolant temperature)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.CHECK HARNESS AND CONNECTOR (OPEN IN WIRE HARNESS)


    A096620E01
  1. Disconnect the D32 ECT sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    140°C (284°F) or more



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


3.CHECK ECM (OPEN IN ECM)


    A099842E04
  1. Disconnect the D32 ECT sensor connector.

  1. Connect terminals THW and E2 of the D1 ECM connector.

    HINT:
    Before checking, perform a visual and contact pressure check on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    140°C (284°F) or more



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

REPLACE ECM 

4.CHECK HARNESS AND CONNECTOR (SHORT IN WIRE HARNESS)


    G038989E01
  1. Disconnect the D32 ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    -40°C (-40°F)



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


5.CHECK ECM (SHORT IN ECM)


    A099843E02
  1. Disconnect the D32 ECT sensor connector.

  1. Disconnect the D1 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain/ ECD / Data List / Coolant Temp.

  1. Read the values.

    Standard:
    -40°C (-40°F)



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR
NG

REPLACE ECM 


When not using intelligent tester:

1.CHECK ECM TERMINAL VOLTAGE (THW TERMINAL)


    A066060E05
  1. Start the engine.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D1-19 (THW) - D1-28 (E2)
    Idling, Engine coolant temperature between 60°C and 120°C (140°F and 248°F)
    0.2 to 1.0 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT ENGINE COOLANT TEMPERATURE SENSOR


    A081700E07
  1. Remove the sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Connection
    Specified Condition
    20°C (68°F)
    2.32 to 2.59 kΩ
    80°C (176°F)
    0.310 to 0.326 kΩ

    NOTICE:
    When checking the ECT sensor in water, keep the terminals dry. After the check, wipe the sensor dry.

    HINT:
    Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR)


    G034905E01
  1. Disconnect the D1 ECM connector.

  1. Disconnect the D32 sensor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D1-19 (THW) - D32-2 (THW)
    Below 1 Ω
    D1-28 (E2) - D32-1 (E2)
    Below 1 Ω
    D1-19 (THW) or D32-2 (THW) - Body ground
    10 kΩ or higher
    D1-28 (E2) or D32-1 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM