Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P2120/19    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122/19    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123/19    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125/19    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127/19    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128/19    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138/19    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.


G036462E01


DTC No.
DTC Detection Condition
(All of following are 1 trip detection logic)
Trouble Area
P2120/19
  1. Condition (a) continues for 0.5 sec. or more:
    1. VPA is 0.2 V or less
    2. VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2122/19
VPA is 0.2 V or less for 0.5 sec. or more when VPA2 output indicate accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCPA circuit
  3. VPA circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2123/19
  1. Condition (a) continues for 2.0 sec. or more:
    1. VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2125/19
  1. Condition (a) or (b) continues for 0.5 sec. or more:
    1. VPA2 is 0.5 V or less
    2. VPA2 is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2127/19
VPA2 is 0.5 V or less for 0.5 sec. or more when VPA output indicates accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. VPA2 circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2128/19
  1. Conditions (a) and (b) continue for 2.0 sec. or more:
    1. VPA2 is 4.8 V or more
    2. VPA is 0.2 V or more and VPA is 3.45 V or less
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2138/19
  1. Condition (a) or (b) continues for 2.0 sec. or more:
    1. Difference between VPA and VPA2 is 0.02 V or less
    2. VPA is 0.2 V or less and VPA2 is 0.5 V or less
  1. VPA and VPA2 circuit are short circuited
  2. Accelerator pedal position sensor
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM

HINT:
When DTC P2120/19, P2122/19, P2123/19, P2125/19, P2127/19, P2128/19 or P2138/19 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the intelligent tester : Powertrain / ECD / Data List / Accel Position 1 and Accel Position 2.


-
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
-
Accelerator pedal released
Accelerator pedal released
Accelerator pedal depressed
Accelerator pedal depressed
Trouble Area
Accelerator Position No.1
Accelerator Position No.2
Accelerator Position No.1
Accelerator Position No.2
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
VPA circuit open or ground short
0 to 0.2 V
1.4 to 1.8 V
0 to 0.2 V
3.7 to 5.0 V
VPA2 circuit open or ground short
0.6 to 1.0 V
0 to 0.2 V
2.9 to 4.2 V
0 to 0.2 V
EP circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V

WIRING DIAGRAM


A110962E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:

1.READ VALUE OF ACCELERATOR PEDAL POSITION SENSOR


    FI07052E07
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / ECD / Data List / Accel Position 1 and Accel Position 2.

  1. Read the values.

    Standard voltage:
    Accelerator Pedal
    Accel Position 1
    Accel Position 2
    Released
    0.6 to 1.0 V
    1.4 to 1.8 V
    Depressed
    2.9 to 4.2 V
    3.7 to 5.0 V



OK
Go to step 5
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A099833E01
  1. Disconnect the B1 sensor connector.

  1. Disconnect the B9 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B1-1 (VCP2) - B9-27 (VCP2)
    B1-2 (EP2) - B9-29 (EPA2)
    B1-3 (VPA2) - B9-23 (VPA2)
    B1-4 (VCP1) - B9-20 (VCPA)
    B1-5 (EP1) - B9-28 (EPA)
    B1-6 (VPA1) - B9-22 (VPA)
    Below 1 Ω
    B1-1 (VCP2) or B9-27 (VCP2) - Body ground
    B1-2 (EP2) or B9-29 (EPA2) - Body ground
    B1-3 (VPA2) or B9-23 (VPA2) - Body ground
    B1-4 (VCP1) or B9-26 (VCPA) - Body ground
    B1-5 (EP1) or B9-28 (EPA) - Body ground
    B1-6 (VPA1) or B9-22 (VPA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)


    A096639E01
  1. Disconnect the B1 sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    B9-26 (VCPA) - B9-28 (EPA)
    B9-27 (VCP2) - B9-29 (EPA2)
    4.5 to 5.0 V



NG
REPLACE ECM
OK


4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


5.CHECK IF OUTPUT DTC RECURS
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the engine at idle for 15 seconds or more.

  1. Read the DTC (Click here).

    Result:

    Display (DTC output)
    Proceed to
    P2120/19, P2122/19, P2123/19, P2125/19, P2127/19, P2128/19 or P2138/19 is output again
    A
    P2120/19, P2122/19, P2123/19, P2125/19, P2127/19, P2128/19orP2138/19 is not output
    B



B
END
A

REPLACE ECM 


When not using intelligent tester:

1.CHECK ECM TERMINAL VOLTAGE (VPA AND VPA2 TERMINALS)


    A066060E09
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Condition
    Accelerator Pedal Condition
    Specified Condition
    B9-22 (VPA) - B9-28 (EPA)
    Released
    0.6 to 1.0 V
    B9-22 (VPA) - B9-28 (EPA)
    Depressed
    2.9 to 4.2 V
    B9-23 (VPA2) - B9-29 (EPA2)
    Released
    1.4 to 1.8 V
    B9-23 (VPA2) - B9-29 (EPA2)
    Depressed
    3.7 to 5.0 V



OK
REPLACE ECM
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A099833E01
  1. Disconnect the B1 sensor connector.

  1. Disconnect the B9 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B1-1 (VCP2) - B9-27 (VCP2)
    B1-2 (EP2) - B9-29 (EPA2)
    B1-3 (VPA2) - B9-23 (VPA2)
    B1-4 (VCP1) - B9-20 (VCPA)
    B1-5 (EP1) - B9-28 (EPA)
    B1-6 (VPA1) - B9-22 (VPA)
    Below 1 Ω
    B1-1 (VCP2) or B9-27 (VCP2) - Body ground
    B1-2 (EP2) or B9-29 (EPA2) - Body ground
    B1-3 (VPA2) or B9-23 (VPA2) - Body ground
    B1-4 (VCP1) or B9-26 (VCPA) - Body ground
    B1-5 (EP1) or B9-28 (EPA) - Body ground
    B1-6 (VPA1) or B9-22 (VPA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)


    A096639E01
  1. Disconnect the B1 sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    B9-26 (VCPA) - B9-28 (EPA)
    B9-27 (VCP2) - B9-29 (EPA2)
    4.5 to 5.0 V



NG
REPLACE ECM
OK


4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NEXT


5.CHECK IF OUTPUT DTC RECURS
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the engine at idle for 15 seconds or more.

  1. Read the DTC (Click here).

    Result:

    Display (DTC output)
    Proceed to
    P2120/19, P2122/19, P2123/19, P2125/19, P2127/19, P2128/19 or P2138/19 is output again
    A
    P2120/19, P2122/19, P2123/19, P2125/19, P2127/19, P2128/19orP2138/19 is not output
    B



B
END
A

REPLACE ECM